2020-10-19 01:09:48 +03:00
/******************************************************************************
* \ attention
*
* < h2 > < center > & copy ; COPYRIGHT 2020 STMicroelectronics < / center > < / h2 >
*
* Licensed under ST MYLIBERTY SOFTWARE LICENSE AGREEMENT ( the " License " ) ;
* You may not use this file except in compliance with the License .
* You may obtain a copy of the License at :
*
* www . st . com / myliberty
*
* Unless required by applicable law or agreed to in writing , software
* distributed under the License is distributed on an " AS IS " BASIS ,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND , either express or implied ,
* AND SPECIFICALLY DISCLAIMING THE IMPLIED WARRANTIES OF MERCHANTABILITY ,
* FITNESS FOR A PARTICULAR PURPOSE , AND NON - INFRINGEMENT .
* See the License for the specific language governing permissions and
* limitations under the License .
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
/*
* PROJECT : ST25R391x firmware
* Revision :
* LANGUAGE : ISO C99
*/
/*! \file rfal_rf.h
*
* \ author Gustavo Patricio
*
* \ brief RF Abstraction Layer ( RFAL )
*
* RFAL ( RF Abstraction Layer ) provides several functionalities required to
* perform RF / NFC communications . < br > The RFAL encapsulates the different
* RF ICs ( ST25R3911 , ST25R391x , etc ) into a common and easy to use interface .
*
* It provides interfaces to configure the RF IC , set / get timings , modes , bit rates ,
* specific handlings , execute listen mode , etc .
*
* Furthermore it provides a common interface to perform a Transceive operations .
* The Transceive can be executed in a blocking or non blocking way . < br >
* Additionally few specific Transceive methods are available to cope with the
* specifics of these particular operations .
*
* The most common interfaces are :
* < br > & nbsp ; rfalInitialize ( )
* < br > & nbsp ; rfalSetFDTPoll ( )
* < br > & nbsp ; rfalSetFDTListen ( )
* < br > & nbsp ; rfalSetGT ( )
* < br > & nbsp ; rfalSetBitRate ( )
* < br > & nbsp ; rfalSetMode ( )
* < br > & nbsp ; rfalFieldOnAndStartGT ( )
* < br > & nbsp ; rfalFieldOff ( )
* < br > & nbsp ; rfalStartTransceive ( )
* < br > & nbsp ; rfalGetTransceiveStatus ( )
* < br > & nbsp ; rfalTransceiveBlockingTxRx ( )
*
* An usage example is provided here : \ ref exampleRfalPoller . c
* \ example exampleRfalPoller . c
*
* \ addtogroup RFAL
* @ {
*
* \ addtogroup RFAL - HAL
* \ brief RFAL Hardware Abstraction Layer
* @ {
*
* \ addtogroup RF
* \ brief RFAL RF Abstraction Layer
* @ {
*
*/
# ifndef RFAL_RF_H
# define RFAL_RF_H
/*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* INCLUDES
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
# include "platform.h"
# include "st_errno.h"
# include "rfal_features.h"
/*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* GLOBAL DEFINES
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
# define RFAL_VERSION 0x020200U /*!< RFAL Current Version: v2.2.0 */
2020-10-19 01:09:48 +03:00
2022-01-05 19:10:18 +03:00
# define RFAL_FWT_NONE 0xFFFFFFFFU /*!< Disabled FWT: Wait forever for a response */
# define RFAL_GT_NONE RFAL_TIMING_NONE /*!< Disabled GT: No GT will be applied after Field On */
2020-10-19 01:09:48 +03:00
2022-01-05 19:10:18 +03:00
# define RFAL_TIMING_NONE 0x00U /*!< Timing disabled | Don't apply */
2020-10-19 01:09:48 +03:00
2022-01-05 19:10:18 +03:00
# define RFAL_1FC_IN_4096FC \
( uint32_t ) 4096U /*!< Number of 1/fc cycles in one 4096/fc */
# define RFAL_1FC_IN_512FC (uint32_t)512U /*!< Number of 1/fc cycles in one 512/fc */
# define RFAL_1FC_IN_64FC (uint32_t)64U /*!< Number of 1/fc cycles in one 64/fc */
# define RFAL_1FC_IN_8FC (uint32_t)8U /*!< Number of 1/fc cycles in one 8/fc */
# define RFAL_US_IN_MS (uint32_t)1000U /*!< Number of us in one ms */
# define RFAL_1MS_IN_1FC (uint32_t)13560U /*!< Number of 1/fc cycles in 1ms */
# define RFAL_BITS_IN_BYTE (uint16_t)8U /*!< Number of bits in one byte */
2020-10-19 01:09:48 +03:00
2022-01-05 19:10:18 +03:00
# define RFAL_CRC_LEN 2U /*!< RF CRC LEN */
2020-10-19 01:09:48 +03:00
/*! Default TxRx flags: Tx CRC automatic, Rx CRC removed, NFCIP1 mode off, AGC On, Tx Parity automatic, Rx Parity removed */
2022-01-05 19:10:18 +03:00
# define RFAL_TXRX_FLAGS_DEFAULT \
( ( uint32_t ) RFAL_TXRX_FLAGS_CRC_TX_AUTO | ( uint32_t ) RFAL_TXRX_FLAGS_CRC_RX_REMV | \
( uint32_t ) RFAL_TXRX_FLAGS_NFCIP1_OFF | ( uint32_t ) RFAL_TXRX_FLAGS_AGC_ON | \
( uint32_t ) RFAL_TXRX_FLAGS_PAR_RX_REMV | ( uint32_t ) RFAL_TXRX_FLAGS_PAR_TX_AUTO | \
( uint32_t ) RFAL_TXRX_FLAGS_NFCV_FLAG_AUTO )
# define RFAL_TXRX_FLAGS_RAW \
( ( uint32_t ) RFAL_TXRX_FLAGS_CRC_TX_MANUAL | ( uint32_t ) RFAL_TXRX_FLAGS_CRC_RX_REMV | \
( uint32_t ) RFAL_TXRX_FLAGS_NFCIP1_OFF | ( uint32_t ) RFAL_TXRX_FLAGS_AGC_ON | \
( uint32_t ) RFAL_TXRX_FLAGS_PAR_RX_REMV | ( uint32_t ) RFAL_TXRX_FLAGS_PAR_TX_NONE | \
( uint32_t ) RFAL_TXRX_FLAGS_NFCV_FLAG_AUTO )
# define RFAL_LM_MASK_NFCA \
( ( uint32_t ) 1U \
< < ( uint8_t ) RFAL_MODE_LISTEN_NFCA ) /*!< Bitmask for Listen Mode enabling NFCA */
# define RFAL_LM_MASK_NFCB \
( ( uint32_t ) 1U \
< < ( uint8_t ) RFAL_MODE_LISTEN_NFCB ) /*!< Bitmask for Listen Mode enabling NFCB */
# define RFAL_LM_MASK_NFCF \
( ( uint32_t ) 1U \
< < ( uint8_t ) RFAL_MODE_LISTEN_NFCF ) /*!< Bitmask for Listen Mode enabling NFCF */
# define RFAL_LM_MASK_ACTIVE_P2P \
( ( uint32_t ) 1U \
< < ( uint8_t ) RFAL_MODE_LISTEN_ACTIVE_P2P ) /*!< Bitmask for Listen Mode enabling AP2P */
# define RFAL_LM_SENS_RES_LEN 2U /*!< NFC-A SENS_RES (ATQA) length */
# define RFAL_LM_SENSB_RES_LEN 13U /*!< NFC-B SENSB_RES (ATQB) length */
# define RFAL_LM_SENSF_RES_LEN 19U /*!< NFC-F SENSF_RES length */
# define RFAL_LM_SENSF_SC_LEN 2U /*!< NFC-F System Code length */
# define RFAL_NFCID3_LEN 10U /*!< NFCID3 length */
# define RFAL_NFCID2_LEN 8U /*!< NFCID2 length */
# define RFAL_NFCID1_TRIPLE_LEN 10U /*!< NFCID1 length */
# define RFAL_NFCID1_DOUBLE_LEN 7U /*!< NFCID1 length */
# define RFAL_NFCID1_SINGLE_LEN 4U /*!< NFCID1 length */
2020-10-19 01:09:48 +03:00
/*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* GLOBAL MACROS
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
/*! Returns the maximum supported bit rate for RW mode. Caller must check if mode is supported before, as even if mode is not supported will return the min */
2022-01-05 19:10:18 +03:00
# define rfalGetMaxBrRW() \
( ( ( RFAL_SUPPORT_BR_RW_6780 ) ? \
RFAL_BR_6780 : \
( ( RFAL_SUPPORT_BR_RW_3390 ) ? \
RFAL_BR_3390 : \
( ( RFAL_SUPPORT_BR_RW_1695 ) ? \
RFAL_BR_1695 : \
( ( RFAL_SUPPORT_BR_RW_848 ) ? \
RFAL_BR_848 : \
( ( RFAL_SUPPORT_BR_RW_424 ) ? \
RFAL_BR_424 : \
( ( RFAL_SUPPORT_BR_RW_212 ) ? RFAL_BR_212 : RFAL_BR_106 ) ) ) ) ) ) )
2020-10-19 01:09:48 +03:00
/*! Returns the maximum supported bit rate for AP2P mode. Caller must check if mode is supported before, as even if mode is not supported will return the min */
2022-01-05 19:10:18 +03:00
# define rfalGetMaxBrAP2P() \
( ( ( RFAL_SUPPORT_BR_AP2P_848 ) ? \
RFAL_BR_848 : \
( ( RFAL_SUPPORT_BR_AP2P_424 ) ? \
RFAL_BR_424 : \
( ( RFAL_SUPPORT_BR_AP2P_212 ) ? RFAL_BR_212 : RFAL_BR_106 ) ) ) )
2020-10-19 01:09:48 +03:00
/*! Returns the maximum supported bit rate for CE-A mode. Caller must check if mode is supported before, as even if mode is not supported will return the min */
2022-01-05 19:10:18 +03:00
# define rfalGetMaxBrCEA() \
( ( ( RFAL_SUPPORT_BR_CE_A_848 ) ? \
RFAL_BR_848 : \
( ( RFAL_SUPPORT_BR_CE_A_424 ) ? \
RFAL_BR_424 : \
( ( RFAL_SUPPORT_BR_CE_A_212 ) ? RFAL_BR_212 : RFAL_BR_106 ) ) ) )
2020-10-19 01:09:48 +03:00
/*! Returns the maximum supported bit rate for CE-B mode. Caller must check if mode is supported before, as even if mode is not supported will return the min */
2022-01-05 19:10:18 +03:00
# define rfalGetMaxBrCEB() \
( ( ( RFAL_SUPPORT_BR_CE_B_848 ) ? \
RFAL_BR_848 : \
( ( RFAL_SUPPORT_BR_CE_B_424 ) ? \
RFAL_BR_424 : \
( ( RFAL_SUPPORT_BR_CE_B_212 ) ? RFAL_BR_212 : RFAL_BR_106 ) ) ) )
2020-10-19 01:09:48 +03:00
/*! Returns the maximum supported bit rate for CE-F mode. Caller must check if mode is supported before, as even if mode is not supported will return the min */
2022-01-05 19:10:18 +03:00
# define rfalGetMaxBrCEF() (((RFAL_SUPPORT_BR_CE_F_424) ? RFAL_BR_424 : RFAL_BR_212))
# define rfalIsModeActiveComm(md) \
( ( ( md ) = = RFAL_MODE_POLL_ACTIVE_P2P ) | | \
( ( md ) = = RFAL_MODE_LISTEN_ACTIVE_P2P ) ) /*!< Checks if mode md is Active Communication */
# define rfalIsModePassiveComm(md) \
( ! rfalIsModeActiveComm ( md ) ) /*!< Checks if mode md is Passive Communication */
# define rfalIsModePassiveListen(md) \
( ( ( md ) = = RFAL_MODE_LISTEN_NFCA ) | | ( ( md ) = = RFAL_MODE_LISTEN_NFCB ) | | \
( ( md ) = = RFAL_MODE_LISTEN_NFCF ) ) /*!< Checks if mode md is Passive Listen */
# define rfalIsModePassivePoll(md) \
( rfalIsModePassiveComm ( md ) & & \
! rfalIsModePassiveListen ( md ) ) /*!< Checks if mode md is Passive Poll */
# define rfalConv1fcTo8fc(t) \
( uint32_t ) ( ( uint32_t ) ( t ) / RFAL_1FC_IN_8FC ) /*!< Converts the given t from 1/fc to 8/fc */
# define rfalConv8fcTo1fc(t) \
( uint32_t ) ( ( uint32_t ) ( t ) * RFAL_1FC_IN_8FC ) /*!< Converts the given t from 8/fc to 1/fc */
# define rfalConv1fcTo64fc(t) \
( uint32_t ) ( ( uint32_t ) ( t ) / RFAL_1FC_IN_64FC ) /*!< Converts the given t from 1/fc to 64/fc */
# define rfalConv64fcTo1fc(t) \
( uint32_t ) ( ( uint32_t ) ( t ) * RFAL_1FC_IN_64FC ) /*!< Converts the given t from 64/fc to 1/fc */
# define rfalConv1fcTo512fc(t) \
( uint32_t ) ( \
( uint32_t ) ( t ) / RFAL_1FC_IN_512FC ) /*!< Converts the given t from 1/fc to 512/fc */
# define rfalConv512fcTo1fc(t) \
( uint32_t ) ( ( uint32_t ) ( t ) * RFAL_1FC_IN_512FC ) /*!< Converts the given t from 512/fc to 1/fc */
# define rfalConv1fcTo4096fc(t) \
( uint32_t ) ( \
( uint32_t ) ( t ) / RFAL_1FC_IN_4096FC ) /*!< Converts the given t from 1/fc to 4096/fc */
# define rfalConv4096fcTo1fc(t) \
( uint32_t ) ( ( uint32_t ) ( t ) * RFAL_1FC_IN_4096FC ) /*!< Converts the given t from 4096/fc to 1/fc */
# define rfalConv1fcToMs(t) \
( uint32_t ) ( ( uint32_t ) ( t ) / RFAL_1MS_IN_1FC ) /*!< Converts the given t from 1/fc to ms */
# define rfalConvMsTo1fc(t) \
( uint32_t ) ( ( uint32_t ) ( t ) * RFAL_1MS_IN_1FC ) /*!< Converts the given t from ms to 1/fc */
# define rfalConv1fcToUs(t) \
( uint32_t ) ( \
( ( uint32_t ) ( t ) * RFAL_US_IN_MS ) / \
RFAL_1MS_IN_1FC ) /*!< Converts the given t from 1/fc to us */
# define rfalConvUsTo1fc(t) \
( uint32_t ) ( \
( ( uint32_t ) ( t ) * RFAL_1MS_IN_1FC ) / \
RFAL_US_IN_MS ) /*!< Converts the given t from us to 1/fc */
# define rfalConv64fcToMs(t) \
( uint32_t ) ( \
( uint32_t ) ( t ) / \
( RFAL_1MS_IN_1FC / RFAL_1FC_IN_64FC ) ) /*!< Converts the given t from 64/fc to ms */
# define rfalConvMsTo64fc(t) \
( uint32_t ) ( \
( uint32_t ) ( t ) * \
( RFAL_1MS_IN_1FC / RFAL_1FC_IN_64FC ) ) /*!< Converts the given t from ms to 64/fc */
# define rfalConvBitsToBytes(n) \
( uint16_t ) ( \
( ( uint16_t ) ( n ) + ( RFAL_BITS_IN_BYTE - 1U ) ) / \
( RFAL_BITS_IN_BYTE ) ) /*!< Converts the given n from bits to bytes */
# define rfalConvBytesToBits(n) \
( uint32_t ) ( \
( uint32_t ) ( n ) * ( RFAL_BITS_IN_BYTE ) ) /*!< Converts the given n from bytes to bits */
2020-10-19 01:09:48 +03:00
/*! Computes a Transceive context \a ctx with default flags and the lengths
* in bytes with the given arguments
* \ a ctx : Transceive context to be assigned
* \ a tB : txBuf the pointer to the buffer to be sent
* \ a tBL : txBuf length in bytes
* \ a rB : rxBuf the pointer to the buffer to place the received frame
* \ a rBL : rxBuf length in bytes
* \ a rBL : rxBuf length in bytes
* \ a t : FWT to be used on this transceive in 1 / fc
*/
2022-01-05 19:10:18 +03:00
# define rfalCreateByteTxRxContext(ctx, tB, tBL, rB, rBL, rdL, t) \
( ctx ) . txBuf = ( uint8_t * ) ( tB ) ; \
( ctx ) . txBufLen = ( uint16_t ) rfalConvBytesToBits ( tBL ) ; \
( ctx ) . rxBuf = ( uint8_t * ) ( rB ) ; \
( ctx ) . rxBufLen = ( uint16_t ) rfalConvBytesToBits ( rBL ) ; \
( ctx ) . rxRcvdLen = ( uint16_t * ) ( rdL ) ; \
( ctx ) . flags = ( uint32_t ) RFAL_TXRX_FLAGS_DEFAULT ; \
( ctx ) . fwt = ( uint32_t ) ( t ) ;
2020-10-19 01:09:48 +03:00
/*! Computes a Transceive context \a ctx using lengths in bytes
* with the given flags and arguments
* \ a ctx : Transceive context to be assigned
* \ a tB : txBuf the pointer to the buffer to be sent
* \ a tBL : txBuf length in bytes
* \ a rB : rxBuf the pointer to the buffer to place the received frame
* \ a rBL : rxBuf length in bytes
* \ a rBL : rxBuf length in bytes
* \ a t : FWT to be used on this transceive in 1 / fc
*/
2022-01-05 19:10:18 +03:00
# define rfalCreateByteFlagsTxRxContext(ctx, tB, tBL, rB, rBL, rdL, fl, t) \
( ctx ) . txBuf = ( uint8_t * ) ( tB ) ; \
( ctx ) . txBufLen = ( uint16_t ) rfalConvBytesToBits ( tBL ) ; \
( ctx ) . rxBuf = ( uint8_t * ) ( rB ) ; \
( ctx ) . rxBufLen = ( uint16_t ) rfalConvBytesToBits ( rBL ) ; \
( ctx ) . rxRcvdLen = ( uint16_t * ) ( rdL ) ; \
( ctx ) . flags = ( uint32_t ) ( fl ) ; \
( ctx ) . fwt = ( uint32_t ) ( t ) ;
# define rfalLogE(...) \
platformLog ( __VA_ARGS__ ) /*!< Macro for the error log method */
# define rfalLogW(...) \
platformLog ( __VA_ARGS__ ) /*!< Macro for the warning log method */
# define rfalLogI(...) \
platformLog ( __VA_ARGS__ ) /*!< Macro for the info log method */
# define rfalLogD(...) \
platformLog ( __VA_ARGS__ ) /*!< Macro for the debug log method */
2020-10-19 01:09:48 +03:00
/*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* GLOBAL ENUMS
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
/* RFAL Guard Time (GT) default values */
2022-01-05 19:10:18 +03:00
# define RFAL_GT_NFCA \
rfalConvMsTo1fc ( \
5U ) /*!< GTA Digital 2.0 6.10.4.1 & B.2 */
# define RFAL_GT_NFCB \
rfalConvMsTo1fc ( \
5U ) /*!< GTB Digital 2.0 7.9.4.1 & B.3 */
# define RFAL_GT_NFCF \
rfalConvMsTo1fc ( \
20U ) /*!< GTF Digital 2.0 8.7.4.1 & B.4 */
# define RFAL_GT_NFCV \
rfalConvMsTo1fc ( \
5U ) /*!< GTV Digital 2.0 9.7.5.1 & B.5 */
# define RFAL_GT_PICOPASS \
rfalConvMsTo1fc ( \
1U ) /*!< GT Picopass */
# define RFAL_GT_AP2P \
rfalConvMsTo1fc ( \
5U ) /*!< TIRFG Ecma 340 11.1.1 */
# define RFAL_GT_AP2P_ADJUSTED \
rfalConvMsTo1fc ( \
5U + \
25U ) /*!< Adjusted GT for greater interoperability (Sony XPERIA P, Nokia N9, Huawei P2) */
2020-10-19 01:09:48 +03:00
/* RFAL Frame Delay Time (FDT) Listen default values */
2022-01-05 19:10:18 +03:00
# define RFAL_FDT_LISTEN_NFCA_POLLER \
1172U /*!< FDTA,LISTEN,MIN (n=9) Last bit: Logic "1" - tnn,min/2 Digital 1.1 6.10 ; EMV CCP Spec Book D v2.01 4.8.1.3 */
# define RFAL_FDT_LISTEN_NFCB_POLLER \
1008U /*!< TR0B,MIN Digital 1.1 7.1.3 & A.3 ; EMV CCP Spec Book D v2.01 4.8.1.3 & Table A.5 */
# define RFAL_FDT_LISTEN_NFCF_POLLER \
2672U /*!< TR0F,LISTEN,MIN Digital 1.1 8.7.1.1 & A.4 */
# define RFAL_FDT_LISTEN_NFCV_POLLER \
4310U /*!< FDTV,LISTEN,MIN t1 min Digital 2.1 B.5 ; ISO15693-3 2009 9.1 */
# define RFAL_FDT_LISTEN_PICOPASS_POLLER \
3400U /*!< ISO15693 t1 min - observed adjustment */
# define RFAL_FDT_LISTEN_AP2P_POLLER \
64U /*!< FDT AP2P No actual FDTListen is required as fields switch and collision avoidance */
# define RFAL_FDT_LISTEN_NFCA_LISTENER \
1172U /*!< FDTA,LISTEN,MIN Digital 1.1 6.10 */
# define RFAL_FDT_LISTEN_NFCB_LISTENER \
1024U /*!< TR0B,MIN Digital 1.1 7.1.3 & A.3 ; EMV CCP Spec Book D v2.01 4.8.1.3 & Table A.5 */
# define RFAL_FDT_LISTEN_NFCF_LISTENER \
2688U /*!< TR0F,LISTEN,MIN Digital 2.1 8.7.1.1 & B.4 */
# define RFAL_FDT_LISTEN_AP2P_LISTENER \
64U /*!< FDT AP2P No actual FDTListen exists as fields switch and collision avoidance */
2020-10-19 01:09:48 +03:00
/* RFAL Frame Delay Time (FDT) Poll default values */
2022-01-05 19:10:18 +03:00
# define RFAL_FDT_POLL_NFCA_POLLER \
6780U /*!< FDTA,POLL,MIN Digital 1.1 6.10.3.1 & A.2 */
# define RFAL_FDT_POLL_NFCA_T1T_POLLER \
384U /*!< RRDDT1T,MIN,B1 Digital 1.1 10.7.1 & A.5 */
# define RFAL_FDT_POLL_NFCB_POLLER \
6780U /*!< FDTB,POLL,MIN = TR2B,MIN,DEFAULT Digital 1.1 7.9.3 & A.3 ; EMVCo 3.0 FDTB,PCD,MIN Table A.5 */
# define RFAL_FDT_POLL_NFCF_POLLER \
6800U /*!< FDTF,POLL,MIN Digital 2.1 8.7.3 & B.4 */
# define RFAL_FDT_POLL_NFCV_POLLER \
4192U /*!< FDTV,POLL Digital 2.1 9.7.3.1 & B.5 */
# define RFAL_FDT_POLL_PICOPASS_POLLER \
1790U /*!< FDT Max */
# define RFAL_FDT_POLL_AP2P_POLLER \
0U /*!< FDT AP2P No actual FDTPoll exists as fields switch and collision avoidance */
2020-10-19 01:09:48 +03:00
/*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* GLOBAL TYPES
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
/*! RFAL modes */
typedef enum {
2022-01-05 19:10:18 +03:00
RFAL_MODE_NONE = 0 , /*!< No mode selected/defined */
RFAL_MODE_POLL_NFCA =
1 , /*!< Mode to perform as NFCA (ISO14443A) Poller (PCD) */
RFAL_MODE_POLL_NFCA_T1T =
2 , /*!< Mode to perform as NFCA T1T (Topaz) Poller (PCD) */
RFAL_MODE_POLL_NFCB =
3 , /*!< Mode to perform as NFCB (ISO14443B) Poller (PCD) */
RFAL_MODE_POLL_B_PRIME =
4 , /*!< Mode to perform as B' Calypso (Innovatron) (PCD) */
RFAL_MODE_POLL_B_CTS =
5 , /*!< Mode to perform as CTS Poller (PCD) */
RFAL_MODE_POLL_NFCF =
6 , /*!< Mode to perform as NFCF (FeliCa) Poller (PCD) */
RFAL_MODE_POLL_NFCV =
7 , /*!< Mode to perform as NFCV (ISO15963) Poller (PCD) */
RFAL_MODE_POLL_PICOPASS =
8 , /*!< Mode to perform as PicoPass / iClass Poller (PCD) */
RFAL_MODE_POLL_ACTIVE_P2P =
9 , /*!< Mode to perform as Active P2P (ISO18092) Initiator */
RFAL_MODE_LISTEN_NFCA =
10 , /*!< Mode to perform as NFCA (ISO14443A) Listener (PICC) */
RFAL_MODE_LISTEN_NFCB =
11 , /*!< Mode to perform as NFCA (ISO14443B) Listener (PICC) */
RFAL_MODE_LISTEN_NFCF =
12 , /*!< Mode to perform as NFCA (ISO15963) Listener (PICC) */
RFAL_MODE_LISTEN_ACTIVE_P2P =
13 /*!< Mode to perform as Active P2P (ISO18092) Target */
2020-10-19 01:09:48 +03:00
} rfalMode ;
/*! RFAL Bit rates */
typedef enum {
2022-01-05 19:10:18 +03:00
RFAL_BR_106 = 0 , /*!< Bit Rate 106 kbit/s (fc/128) */
RFAL_BR_212 = 1 , /*!< Bit Rate 212 kbit/s (fc/64) */
RFAL_BR_424 = 2 , /*!< Bit Rate 424 kbit/s (fc/32) */
RFAL_BR_848 = 3 , /*!< Bit Rate 848 kbit/s (fc/16) */
RFAL_BR_1695 = 4 , /*!< Bit Rate 1695 kbit/s (fc/8) */
RFAL_BR_3390 = 5 , /*!< Bit Rate 3390 kbit/s (fc/4) */
RFAL_BR_6780 = 6 , /*!< Bit Rate 6780 kbit/s (fc/2) */
RFAL_BR_13560 = 7 , /*!< Bit Rate 13560 kbit/s (fc) */
RFAL_BR_52p97 = 0xEB , /*!< Bit Rate 52.97 kbit/s (fc/256) Fast Mode VICC->VCD */
RFAL_BR_26p48 = 0xEC , /*!< Bit Rate 26,48 kbit/s (fc/512) NFCV VICC->VCD & VCD->VICC 1of4 */
RFAL_BR_1p66 = 0xED , /*!< Bit Rate 1,66 kbit/s (fc/8192) NFCV VCD->VICC 1of256 */
RFAL_BR_KEEP = 0xFF /*!< Value indicating to keep the same previous bit rate */
2020-10-19 01:09:48 +03:00
} rfalBitRate ;
/*! RFAL Compliance modes for upper modules */
typedef enum {
2022-01-05 19:10:18 +03:00
RFAL_COMPLIANCE_MODE_NFC , /*!< Perform with NFC Forum 1.1 compliance */
RFAL_COMPLIANCE_MODE_EMV , /*!< Perform with EMVCo compliance */
RFAL_COMPLIANCE_MODE_ISO /*!< Perform with ISO10373 compliance */
} rfalComplianceMode ;
2020-10-19 01:09:48 +03:00
/*! RFAL main states flags */
typedef enum {
2022-01-05 19:10:18 +03:00
RFAL_STATE_IDLE = 0 ,
RFAL_STATE_INIT = 1 ,
RFAL_STATE_MODE_SET = 2 ,
RFAL_STATE_TXRX = 3 ,
RFAL_STATE_LM = 4 ,
RFAL_STATE_WUM = 5
2020-10-19 01:09:48 +03:00
} rfalState ;
/*! RFAL transceive states */
typedef enum {
2022-01-05 19:10:18 +03:00
RFAL_TXRX_STATE_IDLE = 0 ,
RFAL_TXRX_STATE_INIT = 1 ,
RFAL_TXRX_STATE_START = 2 ,
RFAL_TXRX_STATE_TX_IDLE = 11 ,
RFAL_TXRX_STATE_TX_WAIT_GT = 12 ,
RFAL_TXRX_STATE_TX_WAIT_FDT = 13 ,
RFAL_TXRX_STATE_TX_TRANSMIT = 14 ,
RFAL_TXRX_STATE_TX_WAIT_WL = 15 ,
RFAL_TXRX_STATE_TX_RELOAD_FIFO = 16 ,
RFAL_TXRX_STATE_TX_WAIT_TXE = 17 ,
RFAL_TXRX_STATE_TX_DONE = 18 ,
RFAL_TXRX_STATE_TX_FAIL = 19 ,
RFAL_TXRX_STATE_RX_IDLE = 81 ,
RFAL_TXRX_STATE_RX_WAIT_EON = 82 ,
RFAL_TXRX_STATE_RX_WAIT_RXS = 83 ,
RFAL_TXRX_STATE_RX_WAIT_RXE = 84 ,
RFAL_TXRX_STATE_RX_READ_FIFO = 85 ,
RFAL_TXRX_STATE_RX_ERR_CHECK = 86 ,
RFAL_TXRX_STATE_RX_READ_DATA = 87 ,
RFAL_TXRX_STATE_RX_WAIT_EOF = 88 ,
RFAL_TXRX_STATE_RX_DONE = 89 ,
RFAL_TXRX_STATE_RX_FAIL = 90 ,
2020-10-19 01:09:48 +03:00
2022-01-05 19:10:18 +03:00
} rfalTransceiveState ;
2020-10-19 01:09:48 +03:00
/*! RFAL transceive flags */
enum {
2022-01-05 19:10:18 +03:00
RFAL_TXRX_FLAGS_CRC_TX_AUTO =
( 0U
< < 0 ) , /*!< CRC will be generated automatic upon transmission */
RFAL_TXRX_FLAGS_CRC_TX_MANUAL =
( 1U
< < 0 ) , /*!< CRC was calculated manually, included in txBuffer */
RFAL_TXRX_FLAGS_CRC_RX_KEEP =
( 1U
< < 1 ) , /*!< Upon Reception keep the CRC in rxBuffer (reflected on rcvd length) */
RFAL_TXRX_FLAGS_CRC_RX_REMV =
( 0U
< < 1 ) , /*!< Enable CRC check and remove the CRC from rxBuffer */
RFAL_TXRX_FLAGS_NFCIP1_ON =
( 1U
< < 2 ) , /*!< Enable NFCIP1 mode: Add SB(F0) and LEN bytes during Tx and skip SB(F0) byte during Rx */
RFAL_TXRX_FLAGS_NFCIP1_OFF =
( 0U
< < 2 ) , /*!< Disable NFCIP1 mode: do not append protocol bytes while Tx nor skip while Rx */
RFAL_TXRX_FLAGS_AGC_OFF =
( 1U
< < 3 ) , /*!< Disable Automatic Gain Control, improving multiple devices collision detection */
RFAL_TXRX_FLAGS_AGC_ON =
( 0U
< < 3 ) , /*!< Enable Automatic Gain Control, improving single device reception */
RFAL_TXRX_FLAGS_PAR_RX_KEEP =
( 1U
< < 4 ) , /*!< Disable Parity and CRC check and keep the Parity and CRC bits in the received buffer */
RFAL_TXRX_FLAGS_PAR_RX_REMV =
( 0U
< < 0 ) , /*!< Enable Parity check and remove the parity bits from the received buffer */
RFAL_TXRX_FLAGS_PAR_TX_NONE =
( 1U
< < 5 ) , /*!< Disable automatic Parity generation (ISO14443A) and use the one provided in the buffer*/
RFAL_TXRX_FLAGS_PAR_TX_AUTO =
( 0U
< < 5 ) , /*!< Enable automatic Parity generation (ISO14443A) */
RFAL_TXRX_FLAGS_NFCV_FLAG_MANUAL =
( 1U
< < 6 ) , /*!< Disable automatic adaption of flag byte (ISO15693) according to current comm params */
RFAL_TXRX_FLAGS_NFCV_FLAG_AUTO =
( 0U
< < 6 ) , /*!< Enable automatic adaption of flag byte (ISO115693) according to current comm params */
2020-10-19 01:09:48 +03:00
} ;
/*! RFAL error handling */
typedef enum {
2022-01-05 19:10:18 +03:00
RFAL_ERRORHANDLING_NONE =
0 , /*!< No special error handling will be performed */
RFAL_ERRORHANDLING_NFC =
1 , /*!< Error handling set to perform as NFC compliant device */
RFAL_ERRORHANDLING_EMVCO =
2 /*!< Error handling set to perform as EMVCo compliant device */
2020-10-19 01:09:48 +03:00
} rfalEHandling ;
/*! Struct that holds all context to be used on a Transceive */
typedef struct {
2022-01-05 19:10:18 +03:00
uint8_t * txBuf ; /*!< (In) Buffer where outgoing message is located */
uint16_t txBufLen ; /*!< (In) Length of the outgoing message in bits */
uint8_t * rxBuf ; /*!< (Out) Buffer where incoming message will be placed */
uint16_t rxBufLen ; /*!< (In) Maximum length of the incoming message in bits */
uint16_t * rxRcvdLen ; /*!< (Out) Actual received length in bits */
2020-10-19 01:09:48 +03:00
2022-01-05 19:10:18 +03:00
uint32_t flags ; /*!< (In) TransceiveFlags indication special handling */
uint32_t fwt ; /*!< (In) Frame Waiting Time in 1/fc */
} rfalTransceiveContext ;
2020-10-19 01:09:48 +03:00
/*! System callback to indicate an event that requires a system reRun */
2022-01-05 19:10:18 +03:00
typedef void ( * rfalUpperLayerCallback ) ( void ) ;
2020-10-19 01:09:48 +03:00
/*! Callback to be executed before a Transceive */
2022-01-05 19:10:18 +03:00
typedef void ( * rfalPreTxRxCallback ) ( void ) ;
2020-10-19 01:09:48 +03:00
/*! Callback to be executed after a Transceive */
2022-01-05 19:10:18 +03:00
typedef void ( * rfalPostTxRxCallback ) ( void ) ;
2020-10-19 01:09:48 +03:00
/*******************************************************************************/
/* ISO14443A */
/*******************************************************************************/
/*! RFAL ISO 14443A Short Frame Command */
2022-01-05 19:10:18 +03:00
typedef enum {
RFAL_14443A_SHORTFRAME_CMD_WUPA = 0x52 , /*!< ISO14443A WUPA / NFC-A ALL_REQ */
RFAL_14443A_SHORTFRAME_CMD_REQA = 0x26 /*!< ISO14443A REQA / NFC-A SENS_REQ */
2020-10-19 01:09:48 +03:00
} rfal14443AShortFrameCmd ;
/*******************************************************************************/
/*******************************************************************************/
/* FeliCa */
/*******************************************************************************/
2022-01-05 19:10:18 +03:00
# define RFAL_FELICA_LEN_LEN \
1U /*!< FeliCa LEN byte length */
# define RFAL_FELICA_POLL_REQ_LEN \
( RFAL_FELICA_LEN_LEN + 1U + 2U + 1U + \
1U ) /*!< FeliCa Poll Request length (LEN + CMD + SC + RC + TSN) */
# define RFAL_FELICA_POLL_RES_LEN \
( RFAL_FELICA_LEN_LEN + 1U + 8U + 8U + \
2U ) /*!< Maximum FeliCa Poll Response length (LEN + CMD + NFCID2 + PAD + RD) */
# define RFAL_FELICA_POLL_MAX_SLOTS \
16U /*!< Maximum number of slots (TSN) on FeliCa Poll */
2020-10-19 01:09:48 +03:00
/*! NFC-F RC (Request Code) codes NFC Forum Digital 1.1 Table 42 */
2022-01-05 19:10:18 +03:00
enum {
RFAL_FELICA_POLL_RC_NO_REQUEST =
0x00 , /*!< RC: No System Code information requested */
RFAL_FELICA_POLL_RC_SYSTEM_CODE =
0x01 , /*!< RC: System Code information requested */
RFAL_FELICA_POLL_RC_COM_PERFORMANCE =
0x02 /*!< RC: Advanced protocol features supported */
2020-10-19 01:09:48 +03:00
} ;
/*! NFC-F TSN (Time Slot Number) codes NFC Forum Digital 1.1 Table 43 */
2022-01-05 19:10:18 +03:00
typedef enum {
RFAL_FELICA_1_SLOT = 0 , /*!< TSN with number of Time Slots: 1 */
RFAL_FELICA_2_SLOTS = 1 , /*!< TSN with number of Time Slots: 2 */
RFAL_FELICA_4_SLOTS = 3 , /*!< TSN with number of Time Slots: 4 */
RFAL_FELICA_8_SLOTS = 7 , /*!< TSN with number of Time Slots: 8 */
RFAL_FELICA_16_SLOTS = 15 /*!< TSN with number of Time Slots: 16 */
2020-10-19 01:09:48 +03:00
} rfalFeliCaPollSlots ;
/*! NFCF Poll Response NFC Forum Digital 1.1 Table 44 */
typedef uint8_t rfalFeliCaPollRes [ RFAL_FELICA_POLL_RES_LEN ] ;
/*******************************************************************************/
/*******************************************************************************/
2022-01-05 19:10:18 +03:00
/* Listen Mode */
2020-10-19 01:09:48 +03:00
/*******************************************************************************/
/*! RFAL Listen Mode NFCID Length */
2022-01-05 19:10:18 +03:00
typedef enum {
RFAL_LM_NFCID_LEN_04 = RFAL_NFCID1_SINGLE_LEN , /*!< Listen mode indicates 4 byte NFCID */
RFAL_LM_NFCID_LEN_07 = RFAL_NFCID1_DOUBLE_LEN , /*!< Listen mode indicates 7 byte NFCID */
RFAL_LM_NFCID_LEN_10 = RFAL_NFCID1_TRIPLE_LEN , /*!< Listen mode indicates 10 byte NFCID */
2020-10-19 01:09:48 +03:00
} rfalLmNfcidLen ;
/*! RFAL Listen Mode States */
2022-01-05 19:10:18 +03:00
typedef enum {
RFAL_LM_STATE_NOT_INIT = 0x00 , /*!< Not Initialized state */
RFAL_LM_STATE_POWER_OFF = 0x01 , /*!< Power Off state */
RFAL_LM_STATE_IDLE = 0x02 , /*!< Idle state Activity 1.1 5.2 */
RFAL_LM_STATE_READY_A = 0x03 , /*!< Ready A state Activity 1.1 5.3 5.4 & 5.5 */
RFAL_LM_STATE_READY_B = 0x04 , /*!< Ready B state Activity 1.1 5.11 5.12 */
RFAL_LM_STATE_READY_F = 0x05 , /*!< Ready F state Activity 1.1 5.15 */
RFAL_LM_STATE_ACTIVE_A = 0x06 , /*!< Active A state Activity 1.1 5.6 */
RFAL_LM_STATE_CARDEMU_4A = 0x07 , /*!< Card Emulation 4A state Activity 1.1 5.10 */
RFAL_LM_STATE_CARDEMU_4B = 0x08 , /*!< Card Emulation 4B state Activity 1.1 5.14 */
RFAL_LM_STATE_CARDEMU_3 = 0x09 , /*!< Card Emulation 3 state Activity 1.1 5.18 */
RFAL_LM_STATE_TARGET_A = 0x0A , /*!< Target A state Activity 1.1 5.9 */
RFAL_LM_STATE_TARGET_F = 0x0B , /*!< Target F state Activity 1.1 5.17 */
RFAL_LM_STATE_SLEEP_A = 0x0C , /*!< Sleep A state Activity 1.1 5.7 */
RFAL_LM_STATE_SLEEP_B = 0x0D , /*!< Sleep B state Activity 1.1 5.13 */
RFAL_LM_STATE_READY_Ax = 0x0E , /*!< Ready A* state Activity 1.1 5.3 5.4 & 5.5 */
RFAL_LM_STATE_ACTIVE_Ax = 0x0F , /*!< Active A* state Activity 1.1 5.6 */
RFAL_LM_STATE_SLEEP_AF = 0x10 , /*!< Sleep AF state Activity 1.1 5.19 */
2020-10-19 01:09:48 +03:00
} rfalLmState ;
/*! RFAL Listen Mode Passive A configs */
2022-01-05 19:10:18 +03:00
typedef struct {
rfalLmNfcidLen nfcidLen ; /*!< NFCID Len (4, 7 or 10 bytes) */
uint8_t nfcid [ RFAL_NFCID1_TRIPLE_LEN ] ; /*!< NFCID */
uint8_t SENS_RES [ RFAL_LM_SENS_RES_LEN ] ; /*!< NFC-106k; SENS_REQ Response */
uint8_t SEL_RES ; /*!< SEL_RES (SAK) with complete NFCID1 (UID) */
2020-10-19 01:09:48 +03:00
} rfalLmConfPA ;
/*! RFAL Listen Mode Passive B configs */
2022-01-05 19:10:18 +03:00
typedef struct {
uint8_t SENSB_RES [ RFAL_LM_SENSB_RES_LEN ] ; /*!< SENSF_RES */
2020-10-19 01:09:48 +03:00
} rfalLmConfPB ;
/*! RFAL Listen Mode Passive F configs */
2022-01-05 19:10:18 +03:00
typedef struct {
uint8_t SC [ RFAL_LM_SENSF_SC_LEN ] ; /*!< System Code to listen for */
uint8_t SENSF_RES [ RFAL_LM_SENSF_RES_LEN ] ; /*!< SENSF_RES */
2020-10-19 01:09:48 +03:00
} rfalLmConfPF ;
/*******************************************************************************/
/*******************************************************************************/
2022-01-05 19:10:18 +03:00
/* Wake-Up Mode */
2020-10-19 01:09:48 +03:00
/*******************************************************************************/
2022-01-05 19:10:18 +03:00
# define RFAL_WUM_REFERENCE_AUTO 0xFFU /*!< Indicates new reference is set by the driver*/
2020-10-19 01:09:48 +03:00
/*! RFAL Wake-Up Mode States */
2022-01-05 19:10:18 +03:00
typedef enum {
RFAL_WUM_STATE_NOT_INIT = 0x00 , /*!< Not Initialized state */
RFAL_WUM_STATE_ENABLED = 0x01 , /*!< Wake-Up mode is enabled */
RFAL_WUM_STATE_ENABLED_WOKE = 0x02 , /*!< Wake-Up mode enabled and has received IRQ(s)*/
2020-10-19 01:09:48 +03:00
} rfalWumState ;
/*! RFAL Wake-Up Period/Timer */
2022-01-05 19:10:18 +03:00
typedef enum {
RFAL_WUM_PERIOD_10MS = 0x00 , /*!< Wake-Up timer 10ms */
RFAL_WUM_PERIOD_20MS = 0x01 , /*!< Wake-Up timer 20ms */
RFAL_WUM_PERIOD_30MS = 0x02 , /*!< Wake-Up timer 30ms */
RFAL_WUM_PERIOD_40MS = 0x03 , /*!< Wake-Up timer 40ms */
RFAL_WUM_PERIOD_50MS = 0x04 , /*!< Wake-Up timer 50ms */
RFAL_WUM_PERIOD_60MS = 0x05 , /*!< Wake-Up timer 60ms */
RFAL_WUM_PERIOD_70MS = 0x06 , /*!< Wake-Up timer 70ms */
RFAL_WUM_PERIOD_80MS = 0x07 , /*!< Wake-Up timer 80ms */
RFAL_WUM_PERIOD_100MS = 0x10 , /*!< Wake-Up timer 100ms */
RFAL_WUM_PERIOD_200MS = 0x11 , /*!< Wake-Up timer 200ms */
RFAL_WUM_PERIOD_300MS = 0x12 , /*!< Wake-Up timer 300ms */
RFAL_WUM_PERIOD_400MS = 0x13 , /*!< Wake-Up timer 400ms */
RFAL_WUM_PERIOD_500MS = 0x14 , /*!< Wake-Up timer 500ms */
RFAL_WUM_PERIOD_600MS = 0x15 , /*!< Wake-Up timer 600ms */
RFAL_WUM_PERIOD_700MS = 0x16 , /*!< Wake-Up timer 700ms */
RFAL_WUM_PERIOD_800MS = 0x17 , /*!< Wake-Up timer 800ms */
2020-10-19 01:09:48 +03:00
} rfalWumPeriod ;
/*! RFAL Wake-Up Period/Timer */
2022-01-05 19:10:18 +03:00
typedef enum {
RFAL_WUM_AA_WEIGHT_4 = 0x00 , /*!< Wake-Up Auto Average Weight 4 */
RFAL_WUM_AA_WEIGHT_8 = 0x01 , /*!< Wake-Up Auto Average Weight 8 */
RFAL_WUM_AA_WEIGHT_16 = 0x02 , /*!< Wake-Up Auto Average Weight 16 */
RFAL_WUM_AA_WEIGHT_32 = 0x03 , /*!< Wake-Up Auto Average Weight 32 */
2020-10-19 01:09:48 +03:00
} rfalWumAAWeight ;
/*! RFAL Wake-Up Mode configuration */
2022-01-05 19:10:18 +03:00
typedef struct {
rfalWumPeriod period ; /*!< Wake-Up Timer period;how often measurement(s) is performed */
bool irqTout ; /*!< IRQ at every timeout will refresh the measurement(s) */
bool swTagDetect ; /*!< Use SW Tag Detection instead of HW Wake-Up mode */
struct {
bool enabled ; /*!< Inductive Amplitude measurement enabled */
uint8_t delta ; /*!< Delta between the reference and measurement to wake-up */
uint16_t reference ; /*!< Reference to be used;RFAL_WUM_REFERENCE_AUTO sets it auto */
bool autoAvg ; /*!< Use the HW Auto Averaging feature */
bool aaInclMeas ; /*!< When AutoAvg is enabled, include IRQ measurement */
rfalWumAAWeight aaWeight ; /*!< When AutoAvg is enabled, last measure weight */
} indAmp ; /*!< Inductive Amplitude Configuration */
struct {
bool enabled ; /*!< Inductive Phase measurement enabled */
uint8_t delta ; /*!< Delta between the reference and measurement to wake-up */
uint16_t reference ; /*!< Reference to be used;RFAL_WUM_REFERENCE_AUTO sets it auto */
bool autoAvg ; /*!< Use the HW Auto Averaging feature */
bool aaInclMeas ; /*!< When AutoAvg is enabled, include IRQ measurement */
rfalWumAAWeight aaWeight ; /*!< When AutoAvg is enabled, last measure weight */
} indPha ; /*!< Inductive Phase Configuration */
struct {
bool enabled ; /*!< Capacitive measurement enabled */
uint8_t delta ; /*!< Delta between the reference and measurement to wake-up */
uint16_t reference ; /*!< Reference to be used;RFAL_WUM_REFERENCE_AUTO sets it auto */
bool autoAvg ; /*!< Use the HW Auto Averaging feature */
bool aaInclMeas ; /*!< When AutoAvg is enabled, include IRQ measurement */
rfalWumAAWeight aaWeight ; /*!< When AutoAvg is enabled, last measure weight */
} cap ; /*!< Capacitive Configuration */
2020-10-19 01:09:48 +03:00
} rfalWakeUpConfig ;
/*******************************************************************************/
/*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* GLOBAL FUNCTION PROTOTYPES
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Initialize
*
* Initializes RFAL layer and the ST25R391x
* Ensures that ST25R391x is properly connected and returns error if any problem
* is detected
*
* \ warning rfalAnalogConfigInitialize ( ) should be called before so that
* the Analog config table has been previously initialized .
*
* \ return ERR_HW_MISMATCH : Expected HW do not match or communication error
* \ return ERR_NONE : No error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalInitialize ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Calibrate
*
* Performs necessary calibration of RF chip in case it is indicated by current
* register settings . E . g . antenna calibration and regulator calibration
*
* \ return ERR_WRONG_STATE : RFAL not initialized
* \ return ERR_NONE : No error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalCalibrate ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Adjust Regulators
*
* Adjusts ST25R391x regulators
*
* \ param [ out ] result : the result of the calibrate antenna in mV
* NULL if result not requested
*
* \ return ERR_WRONG_STATE : RFAL not initialized
* \ return ERR_NONE : No error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalAdjustRegulators ( uint16_t * result ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set System Callback
*
* Sets a callback for the driver to call when an event has occurred that
* may require the system to be notified
*
* \ param [ in ] pFunc : method pointer for the upper layer callback
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalSetUpperLayerCallback ( rfalUpperLayerCallback pFunc ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set Pre Tx Callback
*
* Sets a callback for the driver to call before a Transceive
*
* \ param [ in ] pFunc : method pointer for the Pre Tx callback
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalSetPreTxRxCallback ( rfalPreTxRxCallback pFunc ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set Post Tx Callback
*
* Sets a callback for the driver to call after a Transceive
*
* \ param [ in ] pFunc : method pointer for the Post Tx callback
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalSetPostTxRxCallback ( rfalPostTxRxCallback pFunc ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Deinitialize
*
* Deinitializes RFAL layer and the ST25R391x
*
* \ return ERR_NONE : No error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalDeinitialize ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set Mode
*
* Sets the mode that RFAL will operate on the following communications .
* Proper initializations will be performed on the ST25R391x
*
* \ warning bit rate value RFAL_BR_KEEP is not allowed , only in rfalSetBitRate ( )
*
* \ warning the mode will be applied immediately on the RFchip regardless of
* any ongoing operations like Transceive , ListenMode
*
* \ param [ in ] mode : mode for the RFAL / RFchip to perform
* \ param [ in ] txBR : transmit bit rate
* \ param [ in ] rxBR : receive bit rate
*
* \ see rfalIsGTExpired
* \ see rfalMode
*
* \ return ERR_WRONG_STATE : RFAL not initialized
* \ return ERR_PARAM : Invalid parameter
* \ return ERR_NONE : No error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalSetMode ( rfalMode mode , rfalBitRate txBR , rfalBitRate rxBR ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Get Mode
*
* Gets the mode that RFAL is set to operate
*
* \ see rfalMode
*
* \ return rfalMode : The current RFAL mode
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
rfalMode rfalGetMode ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set Bit Rate
*
* Sets the Tx and Rx bit rates with the given values
* The bit rate change is applied on the RF chip remaining in the same
* mode previous defined with rfalSetMode ( )
*
* If no mode is defined bit rates will not be applied and an error
* is returned
*
* \ param [ in ] txBR : transmit bit rate
* \ param [ in ] rxBR : receive bit rate
*
* \ see rfalSetMode
* \ see rfalMode
* \ see rfalBitRate
*
* \ return ERR_WRONG_STATE : RFAL not initialized
* \ return ERR_PARAM : Invalid parameter
* \ return ERR_NOT_IMPLEMENTED : Mode not implemented
* \ return ERR_NONE : No error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalSetBitRate ( rfalBitRate txBR , rfalBitRate rxBR ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Get Bit Rate
*
* Gets the Tx and Rx current bit rates
*
* If RFAL is not initialized or mode not set the bit rates return will
* be invalid RFAL_BR_KEEP
*
* \ param [ out ] txBR : RFAL ' s current Tx Bit Rate
* \ param [ out ] rxBR : RFAL ' s current Rx Bit Rate
*
* \ see rfalSetBitRate
* \ see rfalBitRate
*
* \ return ERR_WRONG_STATE : RFAL not initialized or mode not set
* \ return ERR_NONE : No error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalGetBitRate ( rfalBitRate * txBR , rfalBitRate * rxBR ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Set Error Handling Mode
*
* Sets the error handling mode to be used by the RFAL
*
* \ param [ in ] eHandling : the error handling mode
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalSetErrorHandling ( rfalEHandling eHandling ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Get Error Handling Mode
*
* Gets the error handling mode currently used by the RFAL
*
* \ return rfalEHandling : Current error handling mode
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
rfalEHandling rfalGetErrorHandling ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Set Observation Mode
*
* Sets ST25R391x observation modes for RF debug purposes
*
* \ param [ in ] txMode : the observation mode to be used during transmission
* \ param [ in ] rxMode : the observation mode to be used during reception
*
* \ warning The Observation Mode is an advanced feature and should be set
* according to the documentation of the part number in use .
* Please refer to the corresponding Datasheet or Application Note ( s )
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalSetObsvMode ( uint8_t txMode , uint8_t rxMode ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Get Observation Mode
*
* Gets ST25R391x the current configured observation modes
*
* \ param [ in ] txMode : the current observation mode configured for transmission
* \ param [ in ] rxMode : the current observation mode configured for reception
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalGetObsvMode ( uint8_t * txMode , uint8_t * rxMode ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Disable Observation Mode
*
* Disables the ST25R391x observation mode
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalDisableObsvMode ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set FDT Poll
*
* Sets the Frame Delay Time ( FDT ) to be used on the following
* communications .
*
* FDT Poll is the minimum time following a Poll Frame during
* which no subsequent Poll Frame can be sent ( without a response from
* the Listener in between )
* FDTx , PP , MIN - Digital 1.1 6.10 .2 & 7.9 .2 & 8.7 .2
*
* \ param [ in ] FDTPoll : Frame Delay Time in 1 / fc cycles
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalSetFDTPoll ( uint32_t FDTPoll ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set FDT Poll
*
* Gets the current Frame Delay Time ( FDT )
*
* FDT Poll is the minimum time following a Poll Frame during
* which no subsequent Poll Frame can be sent ( without a response from
* the Listener in between )
* FDTx , PP , MIN - Digital 1.1 6.10 .2 & 7.9 .2 & 8.7 .2
*
* \ return FDT : current FDT value in 1 / fc cycles
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
uint32_t rfalGetFDTPoll ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set FDT Listen
*
* Sets the Frame Delay Time ( FDT ) Listen minimum to be used on the
* following communications .
*
* FDT Listen is the minimum time between a Poll Frame and a Listen Frame
* FDTx , LISTEN , MIN - Digital 1.1 6.10 .1 & 7.9 .1 & 8.7 .1
*
* \ param [ in ] FDTListen : Frame Delay Time in 1 / fc cycles
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalSetFDTListen ( uint32_t FDTListen ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set FDT Listen
*
* Gets the Frame Delay Time ( FDT ) Listen minimum
*
* FDT Listen is the minimum time between a Poll Frame and a Listen Frame
* FDTx , LISTEN , MIN - Digital 1.1 6.10 .1 & 7.9 .1 & 8.7 .1
*
* \ return FDT : current FDT value in 1 / fc cycles
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
uint32_t rfalGetFDTListen ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Get GT
*
* Gets the current Guard Time ( GT )
*
* GT is the minimum time when a device in Listen Mode is exposed to an
* unmodulated carrier
*
* \ return GT : Guard Time in 1 / fc cycles
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
uint32_t rfalGetGT ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set GT
*
* Sets the Guard Time ( GT ) to be used on the following communications .
*
* GT is the minimum time when a device in Listen Mode is exposed to an
* unmodulated carrier
*
* \ param [ in ] GT : Guard Time in 1 / fc cycles
* RFAL_GT_NONE if no GT should be applied
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalSetGT ( uint32_t GT ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Is GT expired
*
* Checks whether the GT timer has expired
*
* \ return true : GT has expired or not running
* \ return false : GT is still running
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
bool rfalIsGTExpired ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Turn Field On and Start GT
*
* Turns the Field On , performing Initial Collision Avoidance
*
* After Field On , if GT was set before , it starts the GT timer to be
* used on the following communications .
*
* \ return ERR_RF_COLLISION : External field detected
* \ return ERR_NONE : Field turned On
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalFieldOnAndStartGT ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Turn Field Off
*
* Turns the Field Off
*
* \ return ERR_NONE : Field turned Off
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalFieldOff ( void ) ;
2020-10-19 01:09:48 +03:00
/*****************************************************************************
* Transceive *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Set transceive context
*
* Set the context that will be used for the following Transceive
* Output and input buffers have to be passed and all other details prior to
* the Transceive itself has been started
*
* This method only sets the context , once set rfalWorker has
* to be executed until is done
*
* \ param [ in ] ctx : the context for the following Transceive
*
* \ see rfalWorker
* \ see rfalGetTransceiveStatus
*
* \ return ERR_NONE : Done with no error
* \ return ERR_WRONG_STATE : Not initialized properly
* \ return ERR_PARAM : Invalid parameter or configuration
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalStartTransceive ( const rfalTransceiveContext * ctx ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Get Transceive State
*
* Gets current Transceive internal State
*
* \ return rfalTransceiveState : the current Transceive internal State
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
rfalTransceiveState rfalGetTransceiveState ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Get Transceive Status
*
* Gets current Transceive status
*
* \ return ERR_NONE : Transceive done with no error
* \ return ERR_BUSY : Transceive ongoing
* \ return ERR_XXXX : Error occurred
* \ return ERR_TIMEOUT : No response
* \ return ERR_FRAMING : Framing error detected
* \ return ERR_PAR : Parity error detected
* \ return ERR_CRC : CRC error detected
* \ return ERR_LINK_LOSS : Link Loss - External Field is Off
* \ return ERR_RF_COLLISION : Collision detected
* \ return ERR_IO : Internal error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalGetTransceiveStatus ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Is Transceive in Tx
*
* Checks if Transceive is in Transmission state
*
* \ return true Transmission ongoing
* \ return false Not in transmission state
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
bool rfalIsTransceiveInTx ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Is Transceive in Rx
*
* Checks if Transceive is in Reception state
*
* \ return true Transmission done / reception ongoing
* \ return false Not in reception state
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
bool rfalIsTransceiveInRx ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Get Transceive RSSI
*
* Gets the RSSI value of the last executed Transceive in mV
*
* \ param [ out ] rssi : RSSI value
*
* \ return ERR_NOTSUPP : Feature not supported
* \ return ERR_PARAM : Invalid parameter
* \ return ERR_NONE : No error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalGetTransceiveRSSI ( uint16_t * rssi ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief RFAL Worker
*
* This runs RFAL layer , which drives the actual Transceive procedure
* It MUST be executed frequently in order to execute the RFAL internal
* states and perform the requested operations
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
void rfalWorker ( void ) ;
2020-10-19 01:09:48 +03:00
/*****************************************************************************
* ISO1443A *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Transceives an ISO14443A ShortFrame
*
* Sends REQA to detect if there is any PICC in the field
*
* \ param [ in ] txCmd : Command to be sent :
* 0x52 WUPA / ALL_REQ
* 0x26 REQA / SENS_REQ
*
* \ param [ in ] txCmd : type of short frame to be sent REQA or WUPA
* \ param [ out ] rxBuf : buffer to place the response
* \ param [ in ] rxBufLen : length of rxBuf
* \ param [ out ] rxRcvdLen : received length
* \ param [ in ] fwt : Frame Waiting Time in 1 / fc
*
* \ warning If fwt is set to RFAL_FWT_NONE it will make endlessly for
* a response , which on a blocking method may not be the
* desired usage
*
* \ return ERR_NONE if there is response
* \ return ERR_TIMEOUT if there is no response
* \ return ERR_COLLISION collision has occurred
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalISO14443ATransceiveShortFrame (
rfal14443AShortFrameCmd txCmd ,
uint8_t * rxBuf ,
uint8_t rxBufLen ,
uint16_t * rxRcvdLen ,
uint32_t fwt ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Sends an ISO14443A Anticollision Frame
*
* This is use to perform ISO14443A anti - collision .
* \ note Anticollision is sent without CRC
*
*
* \ param [ in ] buf : reference to ANTICOLLISION command ( with known UID if any ) to be sent ( also out param )
* reception will be place on this buf after bytesToSend
* \ param [ in ] bytesToSend : reference number of full bytes to be sent ( including CMD byte and SEL_PAR )
* if a collision occurs will contain the number of clear bytes
* \ param [ in ] bitsToSend : reference to number of bits ( 0 - 7 ) to be sent ; and received ( also out param )
* if a collision occurs will indicate the number of clear bits ( also out param )
* \ param [ out ] rxLength : reference to the return the received length
* \ param [ in ] fwt : Frame Waiting Time in 1 / fc
*
* \ return ERR_NONE if there is no error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalISO14443ATransceiveAnticollisionFrame (
uint8_t * buf ,
uint8_t * bytesToSend ,
uint8_t * bitsToSend ,
uint16_t * rxLength ,
uint32_t fwt ) ;
2020-10-19 01:09:48 +03:00
/*****************************************************************************
* FeliCa *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief FeliCa Poll
*
* Sends a Poll Request and collects all Poll Responses according to the
* given slots
*
*
* \ param [ in ] slots : number of slots for the Poll Request
* \ param [ in ] sysCode : system code ( SC ) for the Poll Request
* \ param [ in ] reqCode : request code ( RC ) for the Poll Request
* \ param [ out ] pollResList : list of all responses
* \ param [ in ] pollResListSize : number of responses that can be placed in pollResList
* \ param [ out ] devicesDetected : number of cards found
* \ param [ out ] collisionsDetected : number of collisions detected
*
* \ return ERR_NONE if there is no error
* \ return ERR_TIMEOUT if there is no response
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalFeliCaPoll (
rfalFeliCaPollSlots slots ,
uint16_t sysCode ,
uint8_t reqCode ,
rfalFeliCaPollRes * pollResList ,
uint8_t pollResListSize ,
uint8_t * devicesDetected ,
uint8_t * collisionsDetected ) ;
2020-10-19 01:09:48 +03:00
/*****************************************************************************
* ISO15693 *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Sends an ISO15693 Anticollision Frame
*
* This send the Anticollision | Inventory frame ( INVENTORY_REQ )
*
* \ warning rxBuf must be able to contain the payload and CRC
*
* \ param [ in ] txBuf : Buffer where outgoing message is located
* \ param [ in ] txBufLen : Length of the outgoing message in bytes
* \ param [ out ] rxBuf : Buffer where incoming message will be placed
* \ param [ in ] rxBufLen : Maximum length of the incoming message in bytes
* \ param [ out ] actLen : Actual received length in bits
*
* \ return ERR_NONE : Transceive done with no error
* \ return ERR_WRONG_STATE : RFAL not initialized or mode not set
* \ return ERR_IO : Internal error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalISO15693TransceiveAnticollisionFrame (
uint8_t * txBuf ,
uint8_t txBufLen ,
uint8_t * rxBuf ,
uint8_t rxBufLen ,
uint16_t * actLen ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Sends an ISO15693 Anticollision EOF
*
* This sends the Anticollision | Inventory EOF used as a slot marker
*
* \ warning rxBuf must be able to contain the payload and CRC
*
* \ param [ out ] rxBuf : Buffer where incoming message will be placed
* \ param [ in ] rxBufLen : Maximum length of the incoming message in bytes
* \ param [ out ] actLen : Actual received length in bits
*
* \ return ERR_NONE : Transceive done with no error
* \ return ERR_WRONG_STATE : RFAL not initialized or mode not set
* \ return ERR_IO : Internal error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode
rfalISO15693TransceiveEOFAnticollision ( uint8_t * rxBuf , uint8_t rxBufLen , uint16_t * actLen ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Sends an ISO15693 EOF
*
* This is method sends an ISO15693 ( EoF ) used for a Write operation
*
* \ warning rxBuf must be able to contain the payload and CRC
*
* \ param [ out ] rxBuf : Buffer where incoming message will be placed
* \ param [ in ] rxBufLen : Maximum length of the incoming message in bytes
* \ param [ out ] actLen : Actual received length in bytes
*
* \ return ERR_NONE : Transceive done with no error
* \ return ERR_IO : Internal error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalISO15693TransceiveEOF ( uint8_t * rxBuf , uint8_t rxBufLen , uint16_t * actLen ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Transceive Blocking Tx
*
* This is method triggers a Transceive and executes it blocking until the
* Tx has been completed
*
* \ param [ in ] txBuf : Buffer where outgoing message is located
* \ param [ in ] txBufLen : Length of the outgoing message in bytes
* \ param [ out ] rxBuf : Buffer where incoming message will be placed
* \ param [ in ] rxBufLen : Maximum length of the incoming message in bytes
* \ param [ out ] actLen : Actual received length in bits
* \ param [ in ] flags : TransceiveFlags indication special handling
* \ param [ in ] fwt : Frame Waiting Time in 1 / fc
*
* \ return ERR_NONE : Transceive done with no error
* \ return ERR_BUSY : Transceive ongoing
* \ return ERR_XXXX : Error occurred
* \ return ERR_LINK_LOSS : Link Loss - External Field is Off
* \ return ERR_RF_COLLISION : Collision detected
* \ return ERR_IO : Internal error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalTransceiveBlockingTx (
uint8_t * txBuf ,
uint16_t txBufLen ,
uint8_t * rxBuf ,
uint16_t rxBufLen ,
uint16_t * actLen ,
uint32_t flags ,
uint32_t fwt ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Transceive Blocking Rx
*
* This is method executes the reception of an ongoing Transceive triggered
* before by rfalTransceiveBlockingTx ( )
*
* \ return ERR_NONE : Transceive done with no error
* \ return ERR_BUSY : Transceive ongoing
* \ return ERR_XXXX : Error occurred
* \ return ERR_TIMEOUT : No response
* \ return ERR_FRAMING : Framing error detected
* \ return ERR_PAR : Parity error detected
* \ return ERR_CRC : CRC error detected
* \ return ERR_LINK_LOSS : Link Loss - External Field is Off
* \ return ERR_RF_COLLISION : Collision detected
* \ return ERR_IO : Internal error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalTransceiveBlockingRx ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Transceive Blocking
*
* This is method triggers a Transceive and executes it blocking until it
* has been completed
*
* \ param [ in ] txBuf : Buffer where outgoing message is located
* \ param [ in ] txBufLen : Length of the outgoing message in bytes
* \ param [ out ] rxBuf : Buffer where incoming message will be placed
* \ param [ in ] rxBufLen : Maximum length of the incoming message in bytes
* \ param [ out ] actLen : Actual received length in bytes
* \ param [ in ] flags : TransceiveFlags indication special handling
* \ param [ in ] fwt : Frame Waiting Time in 1 / fc
*
* \ return ERR_NONE : Transceive done with no error
* \ return ERR_BUSY : Transceive ongoing
* \ return ERR_XXXX : Error occurred
* \ return ERR_TIMEOUT : No response
* \ return ERR_FRAMING : Framing error detected
* \ return ERR_PAR : Parity error detected
* \ return ERR_CRC : CRC error detected
* \ return ERR_LINK_LOSS : Link Loss - External Field is Off
* \ return ERR_RF_COLLISION : Collision detected
* \ return ERR_IO : Internal error
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalTransceiveBlockingTxRx (
uint8_t * txBuf ,
uint16_t txBufLen ,
uint8_t * rxBuf ,
uint16_t rxBufLen ,
uint16_t * actLen ,
uint32_t flags ,
uint32_t fwt ) ;
2020-10-19 01:09:48 +03:00
/*****************************************************************************
* Listen Mode *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Is external Field On
*
* Checks if external field ( other peer / device ) is on / detected
*
* \ return true External field is On
* \ return false No external field is detected
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
bool rfalIsExtFieldOn ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Listen Mode start
*
* Configures RF Chip to go into listen mode enabling the given technologies
*
*
* \ param [ in ] lmMask : mask with the enabled / disabled listen modes
* use : RFAL_LM_MASK_NFCA ; RFAL_LM_MASK_NFCB ;
* RFAL_LM_MASK_NFCF ; RFAL_LM_MASK_ACTIVE_P2P
* \ param [ in ] confA : pointer to Passive A configurations ( NULL if disabled )
* \ param [ in ] confB : pointer to Passive B configurations ( NULL if disabled )
* \ param [ in ] confF : pointer to Passive F configurations ( NULL if disabled )
* \ param [ in ] rxBuf : buffer to place incoming data
* \ param [ in ] rxBufLen : length in bits of rxBuf
* \ param [ in ] rxLen : pointer to write the data length in bits placed into rxBuf
*
*
* \ return ERR_PARAM Invalid parameter
* \ return ERR_REQUEST Invalid listen mode mask
* \ return ERR_NONE Done with no error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalListenStart (
uint32_t lmMask ,
const rfalLmConfPA * confA ,
const rfalLmConfPB * confB ,
const rfalLmConfPF * confF ,
uint8_t * rxBuf ,
uint16_t rxBufLen ,
uint16_t * rxLen ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Listen Mode start Sleeping
*
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode
rfalListenSleepStart ( rfalLmState sleepSt , uint8_t * rxBuf , uint16_t rxBufLen , uint16_t * rxLen ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Listen Mode Stop
*
* Disables the listen mode on the RF Chip
*
* \ warning the listen mode will be disabled immediately on the RFchip regardless
* of any ongoing operations like Transceive
*
* \ return ERR_NONE Done with no error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalListenStop ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Listen Mode get state
*
* Sets the new state of the Listen Mode and applies the necessary changes
* on the RF Chip
*
* \ param [ out ] dataFlag : indicates that Listen Mode has rcvd data and caller
* must process it . The received message is located
* at the rxBuf passed on rfalListenStart ( ) .
* rfalListenSetState ( ) will clear this flag
* if NULL output parameter will no be written / returned
* \ param [ out ] lastBR : bit rate detected of the last initiator request
* if NULL output parameter will no be written / returned
*
* \ return rfalLmState RFAL_LM_STATE_NOT_INIT : LM not initialized properly
* Any Other : LM State
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
rfalLmState rfalListenGetState ( bool * dataFlag , rfalBitRate * lastBR ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Listen Mode set state
*
* Sets the new state of the Listen Mode and applies the necessary changes
* on the RF Chip
*
* \ param [ in ] newSt : New state to go to
*
* \ return ERR_WRONG_STATE : Not initialized properly
* \ return ERR_PARAM : Invalid parameter
* \ return ERR_NONE : Done with no error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalListenSetState ( rfalLmState newSt ) ;
2020-10-19 01:09:48 +03:00
/*****************************************************************************
* Wake - Up Mode *
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * */
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Wake - Up Mode Start
*
* Sets the RF Chip in Low Power Wake - Up Mode according to the given
* configuration .
*
* \ param [ in ] config : Generic Wake - Up configuration provided by lower
* layers . If NULL will automatically configure the
* Wake - Up mode
*
* \ return ERR_WRONG_STATE : Not initialized properly
* \ return ERR_PARAM : Invalid parameter
* \ return ERR_NONE : Done with no error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalWakeUpModeStart ( const rfalWakeUpConfig * config ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Wake - Up Has Woke
*
* Returns true if the Wake - Up mode is enabled and it has already received
* the indication from the RF Chip that the surrounding environment has changed
* and flagged at least one wake - Up interrupt
*
* \ return true : Wake - Up mode enabled and has received a wake - up IRQ
* \ return false : no Wake - Up IRQ has been received
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
bool rfalWakeUpModeHasWoke ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Wake - Up Mode Stop
*
* Stops the Wake - Up Mode
*
* \ return ERR_WRONG_STATE : Not initialized properly
* \ return ERR_PARAM : Invalid parameter
* \ return ERR_NONE : Done with no error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalWakeUpModeStop ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Low Power Mode Start
*
* Sets the RF Chip in Low Power Mode .
* In this mode the RF Chip is placed in Low Power Mode , similar to Wake - up
* mode but no operation nor period measurement is performed .
* Mode must be terminated by rfalLowPowerModeStop ( )
*
* \ return ERR_WRONG_STATE : Not initialized properly
* \ return ERR_PARAM : Invalid parameter
* \ return ERR_NONE : Done with no error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalLowPowerModeStart ( void ) ;
2020-10-19 01:09:48 +03:00
/*!
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* \ brief Low Power Mode Stop
*
* Stops the Low Power Mode re - enabling the device
*
* \ return ERR_WRONG_STATE : Not initialized properly
* \ return ERR_PARAM : Invalid parameter
* \ return ERR_NONE : Done with no error
*
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*/
2022-01-05 19:10:18 +03:00
ReturnCode rfalLowPowerModeStop ( void ) ;
2020-10-19 01:09:48 +03:00
# endif /* RFAL_RF_H */
/**
* @ }
*
* @ }
*
* @ }
*/
