#define CC1101_STROBE_SFSTXON 0x31 /** Enable and calibrate frequency synthesizer (if MCSM0.FS_AUTOCAL=1). If in RX (with CCA): Go to a wait state where only the synthesizer is running (for quick RX / TX turnaround). */
#define CC1101_STROBE_SXOFF 0x32 /** Turn off crystal oscillator. */
#define CC1101_STROBE_SCAL 0x33 /** Calibrate frequency synthesizer and turn it off. SCAL can be strobed from IDLE mode without setting manual calibration mode (MCSM0.FS_AUTOCAL=0) */
#define CC1101_STROBE_SRX 0x34 /** Enable RX. Perform calibration first if coming from IDLE and MCSM0.FS_AUTOCAL=1. */
#define CC1101_STROBE_STX 0x35 /** In IDLE state: Enable TX. Perform calibration first if MCSM0.FS_AUTOCAL=1. If in RX state and CCA is enabled: Only go to TX if channel is clear. */
#define CC1101_STROBE_SIDLE 0x36 /** Exit RX / TX, turn off frequency synthesizer and exit Wake-On-Radio mode if applicable. */
#define CC1101_STROBE_SWOR 0x38 /** Start automatic RX polling sequence (Wake-on-Radio) as described in Section 19.5 if WORCTRL.RC_PD=0. */
/* 0x37 is unused */
#define CC1101_STROBE_SPWD 0x39 /** Enter power down mode when CSn goes high. */
#define CC1101_STROBE_SFRX 0x3A /** Flush the RX FIFO buffer. Only issue SFRX in IDLE or RXFIFO_OVERFLOW states. */
#define CC1101_STROBE_SFTX 0x3B /** Flush the TX FIFO buffer. Only issue SFTX in IDLE or TXFIFO_UNDERFLOW states. */
#define CC1101_STROBE_SWORRST 0x3C /** Reset real time clock to Event1 value. */
#define CC1101_STROBE_SNOP 0x3D /** No operation. May be used to get access to the chip status byte.*/
/* Status registers, must be accessed with CC1101_BURST, but one by one */
#define CC1101_STATUS_PARTNUM 0x30 /** Chip ID Part Number */
#define CC1101_STATUS_VERSION 0x31 /** Chip ID Version */
#define CC1101_STATUS_FREQEST 0x32 /** Frequency Offset Estimate from Demodulator */
#define CC1101_STATUS_LQI 0x33 /** Demodulator Estimate for Link Quality */
#define CC1101_STATUS_RSSI 0x34 /** Received Signal Strength Indication */
#define CC1101_STATUS_MARCSTATE 0x35 /** Main Radio Control State Machine State */
#define CC1101_STATUS_WORTIME1 0x36 /** High Byte of WOR Time */
#define CC1101_STATUS_WORTIME0 0x37 /** Low Byte of WOR Time */
#define CC1101_STATUS_PKTSTATUS 0x38 /** Current GDOx Status and Packet Status */
#define CC1101_STATUS_VCO_VC_DAC 0x39 /** Current Setting from PLL Calibration Module */
#define CC1101_STATUS_TXBYTES 0x3A /** Underflow and Number of Bytes */
#define CC1101_STATUS_RXBYTES 0x3B /** Overflow and Number of Bytes */
#define CC1101_STATUS_RCCTRL1_STATUS 0x3C /** Last RC Oscillator Calibration Result */
#define CC1101_STATUS_RCCTRL0_STATUS 0x3D /** Last RC Oscillator Calibration Result */
/* Some special registers, use CC1101_BURST to read/write data */
#define CC1101_PATABLE 0x3E /** PATABLE register number, an 8-byte table that defines the PA control settings */
#define CC1101_FIFO 0x3F /** FIFO register nunmber, can be combined with CC1101_WRITE and/or CC1101_BURST */
