unleashed-firmware/bootloader/targets/f7/furi-hal/furi-hal-spi-config.c

#include <furi-hal-spi-config.h>
#include <furi-hal-resources.h>

#define SPI_R SPI1
#define SPI_D SPI2

const LL_SPI_InitTypeDef furi_hal_spi_config_nfc = {
    .Mode = LL_SPI_MODE_MASTER,
    .TransferDirection = LL_SPI_FULL_DUPLEX,
    .DataWidth = LL_SPI_DATAWIDTH_8BIT,
    .ClockPolarity = LL_SPI_POLARITY_LOW,
    .ClockPhase = LL_SPI_PHASE_2EDGE,
    .NSS = LL_SPI_NSS_SOFT,
    .BaudRate = LL_SPI_BAUDRATEPRESCALER_DIV8,
    .BitOrder = LL_SPI_MSB_FIRST,
    .CRCCalculation = LL_SPI_CRCCALCULATION_DISABLE,
    .CRCPoly = 7,
};

const LL_SPI_InitTypeDef furi_hal_spi_config_subghz = {
    .Mode = LL_SPI_MODE_MASTER,
    .TransferDirection = LL_SPI_FULL_DUPLEX,
    .DataWidth = LL_SPI_DATAWIDTH_8BIT,
    .ClockPolarity = LL_SPI_POLARITY_LOW,
    .ClockPhase = LL_SPI_PHASE_1EDGE,
    .NSS = LL_SPI_NSS_SOFT,
    .BaudRate = LL_SPI_BAUDRATEPRESCALER_DIV8,
    .BitOrder = LL_SPI_MSB_FIRST,
    .CRCCalculation = LL_SPI_CRCCALCULATION_DISABLE,
    .CRCPoly = 7,
};

const LL_SPI_InitTypeDef furi_hal_spi_config_display = {
    .Mode = LL_SPI_MODE_MASTER,
    .TransferDirection = LL_SPI_FULL_DUPLEX,
    .DataWidth = LL_SPI_DATAWIDTH_8BIT,
    .ClockPolarity = LL_SPI_POLARITY_LOW,
    .ClockPhase = LL_SPI_PHASE_1EDGE,
    .NSS = LL_SPI_NSS_SOFT,
    .BaudRate = LL_SPI_BAUDRATEPRESCALER_DIV16,
    .BitOrder = LL_SPI_MSB_FIRST,
    .CRCCalculation = LL_SPI_CRCCALCULATION_DISABLE,
    .CRCPoly = 7,
};

/**
 * SD Card in fast mode (after init)
 */
const LL_SPI_InitTypeDef furi_hal_spi_config_sd_fast = {
    .Mode = LL_SPI_MODE_MASTER,
    .TransferDirection = LL_SPI_FULL_DUPLEX,
    .DataWidth = LL_SPI_DATAWIDTH_8BIT,
    .ClockPolarity = LL_SPI_POLARITY_LOW,
    .ClockPhase = LL_SPI_PHASE_1EDGE,
    .NSS = LL_SPI_NSS_SOFT,
    .BaudRate = LL_SPI_BAUDRATEPRESCALER_DIV2,
    .BitOrder = LL_SPI_MSB_FIRST,
    .CRCCalculation = LL_SPI_CRCCALCULATION_DISABLE,
    .CRCPoly = 7,
};

/**
 * SD Card in slow mode (before init)
 */
const LL_SPI_InitTypeDef furi_hal_spi_config_sd_slow = {
    .Mode = LL_SPI_MODE_MASTER,
    .TransferDirection = LL_SPI_FULL_DUPLEX,
    .DataWidth = LL_SPI_DATAWIDTH_8BIT,
    .ClockPolarity = LL_SPI_POLARITY_LOW,
    .ClockPhase = LL_SPI_PHASE_1EDGE,
    .NSS = LL_SPI_NSS_SOFT,
    .BaudRate = LL_SPI_BAUDRATEPRESCALER_DIV32,
    .BitOrder = LL_SPI_MSB_FIRST,
    .CRCCalculation = LL_SPI_CRCCALCULATION_DISABLE,
    .CRCPoly = 7,
};

const FuriHalSpiBus spi_r = {
    .spi = SPI_R,
    .miso = &gpio_spi_r_miso,
    .mosi = &gpio_spi_r_mosi,
    .clk = &gpio_spi_r_sck,
};

const FuriHalSpiBus spi_d = {
    .spi = SPI_D,
    .miso = &gpio_spi_d_miso,
    .mosi = &gpio_spi_d_mosi,
    .clk = &gpio_spi_d_sck,
};

const FuriHalSpiDevice furi_hal_spi_devices[FuriHalSpiDeviceIdMax] = {
    {
        .bus = &spi_r,
        .config = &furi_hal_spi_config_subghz,
        .chip_select = &gpio_subghz_cs,
    },
    {
        .bus = &spi_d,
        .config = &furi_hal_spi_config_display,
        .chip_select = &gpio_display_cs,
    },
    {
        .bus = &spi_d,
        .config = &furi_hal_spi_config_sd_fast,
        .chip_select = &gpio_sdcard_cs,
    },
    {
        .bus = &spi_d,
        .config = &furi_hal_spi_config_sd_slow,
        .chip_select = &gpio_sdcard_cs,
    },
    {.bus = &spi_r, .config = &furi_hal_spi_config_nfc, .chip_select = &gpio_nfc_cs},
};