This commit converts naked `new`s to `AK::try_make` and `AK::try_create`
wherever possible. If the called constructor is private, this can not be
done, so we instead now use the standard-defined and compiler-agnostic
`new (nothrow)`.
If we are in a shared interrupt handler, the called handlers might
indicate it was not their interrupt, so we should not increment the
call counter of these handlers.
Previously we would not block the caller until the connection was
established and would instead return EPIPE for the first send() call
which then likely caused the caller to abandon the socket.
This was broken by 0625342.
These are pretty common on older LGA1366 & LGA1150 motherboards.
NOTE: Since the registers datasheets for all versions of the chip
besides versions 1 - 3 are still under NDAs i had to collect
several "magical vendor constants" from the *BSD driver and the
linux driver that i was not able to name verbosely, and as such
these are labeled with the comment "vendor magic values".
We call it E1000E, because the layout for these cards is somewhat not
the same like E1000 supported cards.
Also, this card supports advanced features that are not supported on
8254x cards.
Instead of initializing network adapters in init.cpp, let's move that
logic into a separate class to handle this.
Also, it seems like a good idea to shift responsiblity on enumeration
of network adapters after the boot process, so this singleton will take
care of finding the appropriate network adapter when asked to with an
IPv4 address or interface name.
With this change being merged, we simplify the creation logic of
NetworkAdapter derived classes, so we enumerate the PCI bus only once,
searching for driver candidates when doing so, and we let each driver
to test if it is resposible for the specified PCI device.
When attempting to write to a socket that is not connected or - for
connection-less protocols - doesn't have a peer address set we should
return EPIPE instead of blocking the thread.
When receiving a SYN packet for a connection that's in the "SYN
received" state we should ignore the duplicate SYN packet instead of
closing the connection. This can happen when we didn't accept the
connection in time and our peer has sent us another SYN packet because
it thought that the initial SYN packet was lost.
Previously we wouldn't release the buffer back to the network adapter
in all cases. While this didn't leak the buffer it would cause the
buffer to not be reused for other packets.
Previously we'd just dump those packets into the network adapter's
send queue and hope for the best. Instead we should wait until the peer
has sent TCP ACK packets.
Ideally this would parse the TCP window size option from the SYN or
SYN|ACK packet, but for now we just assume the window size is 64 kB.
Previously we'd allocate buffers when sending packets. This patch
avoids these allocations by using the NetworkAdapter's packet queue.
At the same time this also avoids copying partially constructed
packets in order to prepend Ethernet and/or IPv4 headers. It also
properly truncates UDP and raw IP packets.
Previously TCPSocket::send_tcp_packet() would try to send TCP packets
which matched whatever size the userspace program specified. We'd try to
break those packets up into smaller fragments, however a much better
approach is to limit TCP packets to the maximum segment size and
avoid fragmentation altogether.
There's no good reason to distinguish between network interfaces based
on their model. It's probably a good idea to try keep the names more
persistent so scripts written for a specific network interface will be
useable after hotplug event (or after rebooting with new hardware
setup).
Problem:
- `static` variables consume memory and sometimes are less
optimizable.
- `static const` variables can be `constexpr`, usually.
- `static` function-local variables require an initialization check
every time the function is run.
Solution:
- If a global `static` variable is only used in a single function then
move it into the function and make it non-`static` and `constexpr`.
- Make all global `static` variables `constexpr` instead of `const`.
- Change function-local `static const[expr]` variables to be just
`constexpr`.
This avoids two allocations when receiving network packets. One for
inserting a PacketWithTimestamp into m_packet_queue and another one
when inserting buffers into the list of unused packet buffers.
With this fixed the only allocations in NetworkTask happen when
initially allocating the PacketWithTimestamp structs and when switching
contexts.
Occasionally we'll see messages in the serial console like:
handle_tcp: unexpected flags in FinWait1 state
In these cases it would be nice to know what flags we are receiving that
we aren't expecting.
Previously we didn't retransmit lost TCP packets which would cause
connections to hang if packets were lost. Also we now time out
TCP connections after a number of retransmission attempts.
This wakes up NetworkTask every 500 milliseconds so that it can send
pending delayed TCP ACKs and isn't forced to send all of them early
when it goes to sleep like it did before.
When establishing the connection we should send ACKs right away so
as to not delay the connection process. This didn't previously
matter because we'd flush all delayed ACKs when NetworkTask waits
for incoming packets.
Avoid holding the sockets_by_tuple lock while allocating the TCPSocket.
While checking if the list contains the item we can also hold the lock
in shared mode, as we are only reading the hash table.
In addition the call to from_tuple appears to be superfluous, as we
created the socket, so we should be able to just return it directly.
This avoids the recursive lock acquisition, as well as the unnecessary
hash table lookups.
