ladybird/Kernel/Devices/FloppyDiskDevice.h

/*
 * Copyright (c) 2019-2020, Jesse Buhagiar <jooster669@gmail.com>
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice, this
 *    list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

//
// Intel 82078 Floppy Disk controller driver
// Datasheet: https://wiki.qemu.org/images/f/f0/29047403.pdf
//
// The Intel 82078 is a 44-pin package, CHMOS Single Chip Floppy Disk Controller found commonly
// on later PCs in the mid to late 90s. It supports a multitude of floppy drives found in computers
// at the time, up to and including 2.8MB ED Floppy Disks and is software compatible with previous FDCs.
// Drive in this case refers to the actual drive where the media is inserted and a disk is the actual
// magnetic floppy disk media. This controller is emulated by QEMU.
//
// Certain terminology exists in the code of this driver that may be confusing, being that there
// is a lot of code and documentation online that is seemingly conflicting. I've used terms found
// directly in the datasheet however for the sake of completeness I'll explain them here:
//
//      - Cylinder: One full circular 'slice' of the floppy disk. It contains 18 sectors
//                  on a 3.5" floppy disk. It is also known as a 'track'. There are
//                  80 tracks on a single side of a floppy disk.
//      - Sector:   One 512 byte chunk of a track.
//      - Head:     The read write arm found inside the drive itself. On a double sided
//                  floppy disk drive, there are two, one for the top tracks of the disk
//                  and the other for the bottom tracks.
//      - CHS:      Cylinder, Head, Sector. The addressing type this floppy controller
//                  uses to address the disk geometry.
//
// A normal PC System usually contains one or two floppy drives. This controller contains the
// ability to control up to four drives with the one controller, however it is very rare for
// most systems to contain this amount of drives.
//
// The basic operation of the drive involves reseting the drive in hardware, then sending command
// bytes to the FIFO, allowing the command to execute, then flushing the FIFO by reading `n` bytes
// from it. Most commands are multi-parameter and multi-result, so it's best to consult the datasheet
// from page 23. It is recommended that a SENSE command is performed to retrieve valubable interrupt
// information about the performed action.
//
// Reseting the controller involves the following:
//      - Acquire the version ID of the controller.
//      - Reset the DOR register
//      - Deassert software reset bit in the DOR register and assert the DMAGATE pin to initialize DMA mode
//      - Program the Configuration Control Register (CCR) for 3.5" 1.44MB diskettes
//      - Send a SPECIFY command to specify more drive information. Refer to the datasheet
//
// The drive (being mapped to the controller) will then be in a state that will accept the correct media.
// The DMA controller is also set up here, which is on channel 2. This only needs to be done once, the
// read and write commands can toggle the appropriate bits themselves to allow a specific transfer direction.
//
// Recalibrating the drive refers to the act of resetting the head of the drive back to track/cylinder 0. It
// is essentially the same as a seek, however returning the drive to a known position. For the sake of brevity,
// only the recalibrate sequence will be described.
//
//      - Enable the drive and it's motor (all drive motors are manually enabled by us!).
//      - Issue a recalibrate or a seek command
//      - Wait for interrupt
//      - Issue a SENSE command, letting the drive know we handled the interrupt
//      - Flush the FIFO and check the cylinder value to ensure we are at the correct spot.
//
// Once this has been completed, the drive will either be at the desired position or back at cylinder 0.
//
// To perform a READ or a WRITE of the diskette inserted, the following actions must be taken:
//
//      -The drive and it's motor must be enabled
//      -The data rate must be set via CCR
//      -The drive must be then recalibrated to ensure the head has not drifted.
//      -A wait of 500ms or greater must occur to allow the drive to spin up from inertia.
//      -The DMA direction of the transfer is then configured.
//      -The READ or WRITE command is issued to the controller.
//      -A timeout counter is started. This is only for real hardware and is currently not implemented.
//      -Read the result bytes.
//      -Attempt to READ or WRITE to the disk. Intel recommends doing this a max of 3 times before failing.
//
//
//
#pragma once

#include <AK/RefPtr.h>
#include <Kernel/Devices/BlockDevice.h>
#include <Kernel/Interrupts/IRQHandler.h>
#include <Kernel/Lock.h>
#include <Kernel/VM/PhysicalPage.h>
#include <LibBareMetal/Memory/PhysicalAddress.h>

namespace Kernel {

struct FloppyControllerCommand {
    u8 cmd;         // Command to send to the controller
    u8 numParams;   // Number of parameters to send to the drive
    u8 numReturned; // Number of values we expect to be returned by the command
    u8* params;
    u8* result;
};

//
// NOTE: This class only supports 3.5" 1.44MB floppy disks!
// Any other type of drive will be ignored
//
// Also not that the floppy disk controller is set up to be in PS/2 mode, which
// uses the Intel 82077A controller. More about this controller can
// be found here: http://www.buchty.net/casio/files/82077.pdf
//
class FloppyDiskDevice final
    : public IRQHandler
    , public BlockDevice {
    AK_MAKE_ETERNAL

    static constexpr u8 SECTORS_PER_CYLINDER = 18;
    static constexpr u8 CYLINDERS_PER_HEAD = 80;
    static constexpr u16 BYTES_PER_SECTOR = 512;

public:
    //
    // Is this floppy drive the master or the slave on the controller??
    //
    enum class DriveType : u8 {
        Master,
        Slave
    };

private:
    // Floppy commands
    enum class FloppyCommand : u8 {
        ReadTrack = 0x02,
        Specify = 0x03,
        CheckStatus = 0x04,
        WriteData = 0x05,
        ReadData = 0x06,
        Recalibrate = 0x07,
        SenseInterrupt = 0x08,
        WriteDeletedData = 0x09,
        ReadDeletedData = 0x0C,
        FormatTrack = 0x0D,
        Seek = 0x0F,
        Version = 0x10,
        Verify = 0x16,
    };

public:
    static NonnullRefPtr<FloppyDiskDevice> create(DriveType);
    virtual ~FloppyDiskDevice() override;

    // ^DiskDevice
    virtual bool read_blocks(unsigned index, u16 count, u8*) override;
    virtual bool write_blocks(unsigned index, u16 count, const u8*) override;

    // ^BlockDevice
    virtual ssize_t read(FileDescription&, u8*, ssize_t) override { return 0; }
    virtual bool can_read(const FileDescription&) const override { return true; }
    virtual ssize_t write(FileDescription&, const u8*, ssize_t) override { return 0; }
    virtual bool can_write(const FileDescription&) const override { return true; }

    virtual const char* purpose() const override { return "Floppy Disk Controller"; }

protected:
    explicit FloppyDiskDevice(DriveType);

private:
    // ^IRQHandler
    virtual void handle_irq(RegisterState&) override;

    // ^DiskDevice
    virtual const char* class_name() const override;

    // Helper functions
    inline u16 lba2head(u16 lba) const { return (lba % (SECTORS_PER_CYLINDER * 2)) / SECTORS_PER_CYLINDER; } // Convert an LBA into a head value
    inline u16 lba2cylinder(u16 lba) const { return lba / (2 * SECTORS_PER_CYLINDER); }                      // Convert an LBA into a cylinder value
    inline u16 lba2sector(u16 lba) const { return ((lba % SECTORS_PER_CYLINDER) + 1); }                      // Convert an LBA into a sector value

    void initialize();
    bool read_sectors_with_dma(u16, u16, u8*);
    bool write_sectors_with_dma(u16, u16, const u8*);
    bool wait_for_irq();

    bool is_busy() const;
    bool seek(u16);
    bool recalibrate();

    void send_byte(u8) const;
    void send_byte(FloppyCommand) const;

    void write_dor(u8) const;
    void write_ccr(u8) const;
    void motor_enable(bool) const;
    void configure_drive(u8, u8, u8) const;

    u8 read_byte() const;
    u8 read_msr() const;

    bool is_slave() const { return m_drive_type == DriveType::Slave; }

    Lock m_lock { "FloppyDiskDevice" };
    u16 m_io_base_addr { 0 };
    volatile bool m_interrupted { false };

    DriveType m_drive_type { DriveType::Master };
    RefPtr<PhysicalPage> m_dma_buffer_page;

    u8 m_controller_version { 0 };
};

}