mirror of
https://github.com/pirate/wireguard-docs.git
synced 2024-08-16 20:20:50 +03:00
remove references to /etc/wireguard
This commit is contained in:
parent
38dda69627
commit
d13f79f11d
23
README.md
23
README.md
@ -381,14 +381,14 @@ Overview of the general process:
|
||||
|
||||
1. Install `apt install wireguard` or `pkg/brew install wireguard-tools` on each node
|
||||
2. Generate public and private keys locally on each node `wg genkey`+`wg pubkey`
|
||||
3. Create a `/etc/wireguard/wg0.conf` WireGuard config file on the main relay server
|
||||
3. Create a `wg0.conf` WireGuard config file on the main relay server
|
||||
- `[Interface]` Make sure to specify a CIDR range for the entire VPN subnet when defining the address the server accepts routes for `Address = 192.0.2.1/24`
|
||||
- `[Peer]` Create a peer section for every client joining the VPN, using their corresponding remote public keys
|
||||
4. Create a `/etc/wireguard/wg0.conf` WireGuard config file on each client node
|
||||
4. Create a `wg0.conf` on each client node
|
||||
- `[Interface]` Make sure to specify only a single IP for client peers that don't relay traffic `Address = 192.0.2.3/32`.
|
||||
- `[Peer]` Create a peer section for each public peer not behind a NAT, make sure to specify a CIDR range for the entire VPN subnet when defining the remote peer acting as the bounce server `AllowedIPs = 192.0.2.1/24`. Make sure to specify individual IPs for remote peers that don't relay traffic and only act as simple clients `AllowedIPs = 192.0.2.3/32`.
|
||||
5. Start WireGuard on the main relay server with `wg-quick up /etc/wireguard/wg0.conf`
|
||||
6. Start WireGuard on all the client peers with `wg-quick up /etc/wireguard/wg0.conf`
|
||||
5. Start WireGuard on the main relay server with `wg-quick up /full/path/to/wg0.conf`
|
||||
6. Start WireGuard on all the client peers with `wg-quick up /full/path/to/wg0.conf`
|
||||
7. Traffic is routed from peer to peer using most specific route first over the WireGuard interface, e.g. `ping 192.0.2.3` checks for a direct route to a peer with `AllowedIPs = 192.0.2.3/32` first, then falls back to a relay server that's accepting ips in the whole subnet
|
||||
|
||||
### Setup
|
||||
@ -439,9 +439,8 @@ wg pubkey < example.key > example.key.pub
|
||||
### Start / Stop
|
||||
|
||||
```bash
|
||||
# first, create a configuration file at /etc/wireguard/wg0.conf
|
||||
wg-quick up /etc/wireguard/wg0.conf
|
||||
wg-quick down /etc/wireguard/wg0.conf
|
||||
wg-quick up /full/path/to/wg0.conf
|
||||
wg-quick down /full/path/to/wg0.conf
|
||||
# Note: you must specify the absolute path to wg0.conf, relative paths won't work
|
||||
```
|
||||
|
||||
@ -570,14 +569,12 @@ dig example.com A
|
||||
|
||||
### Overview
|
||||
|
||||
WireGuard config files are in INI syntax. The configuration is specified as an argument when running any `wg-quick` command, e.g.:
|
||||
WireGuard config is in INI syntax, defined in a file usually called `wg0.conf`. It can be placed anywhere on the system, but is often placed in `/etc/wireguard/wg0.conf`.
|
||||
|
||||
```bash
|
||||
# you must use an absolute path; relative paths won't work
|
||||
wq-quick up /etc/wireguard/wg0.conf
|
||||
```
|
||||
The config path is specified as an argument when running any `wg-quick` command, e.g:
|
||||
`wg-quick up /etc/wireguard/wg0.conf` (always specify the full, absolute path)
|
||||
|
||||
The file name must be in the format `${name of the new wireguard interface}.conf`. `wg-quick` looks for config files in `/etc/wireguard` by default, so it usually makes sense to place them there. Wireguard interface names are typically prefixed with `wg` and numbered starting at `0`, but you can use any name that matches the regex `^[a-zA-Z0-9_=+.-]{1,15}$`. A configuration file for the interface `wg0` would typically be found at `/etc/wireguard/wg0.conf`.
|
||||
The config file name must be in the format `${name of the new wireguard interface}.conf`. WireGuard interface names are typically prefixed with `wg` and numbered starting at `0`, but you can use any name that matches the regex `^[a-zA-Z0-9_=+.-]{1,15}$`.
|
||||
|
||||
Config files can opt to use the limited set of `wg` config options, or the more extended `wg-quick` options, depending on what command is preferred to start WireGuard. These docs recommend sticking to `wg-quick` as it provides a more powerful and user-friendly config experience.
|
||||
|
||||
|
Loading…
Reference in New Issue
Block a user