mirror of
https://github.com/InfiniTimeOrg/InfiniTime.git
synced 2024-12-25 02:32:41 +03:00
53 lines
2.3 KiB
Markdown
53 lines
2.3 KiB
Markdown
# Build a stub for PineTime using NRF52-DK
|
|
|
|
[NRF52-DK](https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52-DK) is the official development kit for the NRF52832 SoC from Nordic Semiconductor used in the PineTime.
|
|
|
|
This development kit can be very useful for PineTime development:
|
|
|
|
- You can use its embedded JLink SWD programmer/debugger to program and debug your code on the PineTime
|
|
- As it's based on the same SoC than the PineTime, you can program it to actually run the same code as the PineTime.
|
|
|
|
This page is about the 2nd point. We will build a stub that will allow us to run the same code you can run on the PineTime. This will allow you to work more easily if you don't have a PineTime dev kit around, if you don't want to modify your dev kit for SWD programming, or if you want to use some feature from the NRF52-DK (like power measurement).
|
|
|
|
This stub only implements the display, the button and the BLE radio. The other features from the pintime are missing:
|
|
|
|
- heart rate sensor
|
|
- SPI flash
|
|
- touchpad
|
|
- accelerometer
|
|
|
|
These devices could be added on this stub, but I do not have the parts to try them out for now.
|
|
|
|
|
|
|
|
Here are the parts you need to build this simulator:
|
|
|
|
- [NRF52-DK](https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52-DK)
|
|
- An ST7889 display (I bought [this one](https://www.aliexpress.com/item/32859772356.html?spm=a2g0s.9042311.0.0.1b774c4dSoc4Xz))
|
|
- A push-button (the one I use comes from a previous project build around ESP8266 board Wemos D1 Mini).
|
|
- Dupont wires
|
|
|
|
You just need to make the following connections:
|
|
|
|
| NRF52-DK | ST7889 display |
|
|
| -------- | -------------- |
|
|
| VDD | VCC |
|
|
| GND | GND |
|
|
| P0.03 | SDA |
|
|
| P0.26 | RES |
|
|
| P0.02 | SCL |
|
|
| P0.18 | DC |
|
|
|
|
| NRF52-DK | Push Button |
|
|
| -------- | ------------------------- |
|
|
| P0.13 | Button IN (D3 in my case) |
|
|
| GND | GND |
|
|
|
|
You also need to enable the I/O expander to disconnect pins from the buttons and LED on the NRF52-DK and leave them available on the pin headers:
|
|
|
|
| NRF52 -DK | NRF52- DK |
|
|
| --------- | --------- |
|
|
| DETECT | GND |
|
|
|
|
Now, you should be able to program the SoC on the NRF52-DK board, and use it as if it was running on the PineTime.
|