mirror of
https://github.com/InfiniTimeOrg/InfiniTime.git
synced 2024-11-28 05:56:00 +03:00
105 lines
3.5 KiB
Markdown
105 lines
3.5 KiB
Markdown
# OpenOCD and STLink
|
|
OpenOCD (**Open O**n **C**hip **D**ebugger) is an open source tool that interfaces with many SWD/JTAG debugger to provide debugging and *in-system* programming for embedded target devices.
|
|
|
|
It supports the **NRF52** (the CPU of the PineTime) and the **STLinkV2**, a cheap SWD debugger.
|
|
|
|
It works on X86 computers, as well as ARM/ARM64 computers and SBC (like the RaspberryPi and Pine64 Pinebook Pro) !
|
|
|
|
## Installation
|
|
We will build OpenOCD from sources, as packages from Linux distributions are most of the time outdated and do not support the NRF52 correctly.
|
|
|
|
- Fetch the sources from GIT, and build and install it:
|
|
|
|
```
|
|
git clone https://git.code.sf.net/p/openocd/code openocd-code
|
|
|
|
cd openocd-code
|
|
|
|
./bootstrap
|
|
./configure --enable-stlink
|
|
make -j 4
|
|
sudo make install
|
|
```
|
|
|
|
- Configure UDEV to allow OpenOCD to open the interface to your STLinkV2:
|
|
```
|
|
sudo cp contrib/60-openocd.rules /etc/udev/rules.d/
|
|
sudo udevadm control --reload-rules
|
|
```
|
|
|
|
- You can now plug your STLinkV2 in a USB port and run OpenOCD to see if it's working correctly:
|
|
|
|
```
|
|
$ openocd -f interface/stlink.cfg -f target/nrf52.cfg
|
|
Open On-Chip Debugger 0.10.0+dev-01411-g051e80812-dirty (2020-09-28-20:16)
|
|
Licensed under GNU GPL v2
|
|
For bug reports, read
|
|
http://openocd.org/doc/doxygen/bugs.html
|
|
Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'.
|
|
Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD
|
|
|
|
nRF52 device has a CTRL-AP dedicated to recover the device from AP lock.
|
|
A high level adapter (like a ST-Link) you are currently using cannot access
|
|
the CTRL-AP so 'nrf52_recover' command will not work.
|
|
Do not enable UICR APPROTECT.
|
|
|
|
Info : Listening on port 6666 for tcl connections
|
|
Info : Listening on port 4444 for telnet connections
|
|
Info : clock speed 1000 kHz
|
|
Info : STLINK V2J34S7 (API v2) VID:PID 0483:3748
|
|
Info : Target voltage: 3.294340
|
|
Error: init mode failed (unable to connect to the target)
|
|
```
|
|
Ok, OpenOCD is running and it detects my STLinkV2. The last error shows that I've not connected the STLinkV2 to the PineTime.
|
|
|
|
## Configuration files
|
|
OpenOCD is configured using configuration files.
|
|
First, we need a common configuration file for the project : **openocd-stlink.ocd**:
|
|
```
|
|
source [find interface/stlink.cfg]
|
|
|
|
gdb_flash_program enable
|
|
gdb_breakpoint_override hard
|
|
|
|
source [find target/nrf52.cfg]
|
|
```
|
|
This file specifies to OpenOCD which debugger and target it will be connected to..
|
|
|
|
Then, we use various *user files* to use OpenOCD to flash InfiniTime binary files.
|
|
|
|
This files flashes the bootloader and the application firmware : **flash_bootloader_app.ocd**:
|
|
```
|
|
init
|
|
|
|
program <build directory>/bootloader.bin verify 0x00000000
|
|
program <build directory>/image-0.8.2.bin verify 0x00008000
|
|
|
|
reset
|
|
```
|
|
|
|
And this one flashes the graphics flasher (it writes the bootloader graphics into the SPI NOR flash memory) : **flash_graphics.ocd**:
|
|
```
|
|
init
|
|
|
|
program <build directory>/pinetime-graphics-0.8.2.bin verify 0x00000000
|
|
|
|
reset
|
|
```
|
|
|
|
## Examples
|
|
### Flash bootloader and application
|
|
```
|
|
openocd -f ./openocd-stlink.cfg -f ./flash_bootloader_app.ocd
|
|
```
|
|
|
|
### Flash graphics flasher
|
|
```
|
|
openocd -f ./openocd-stlink.cfg -f ./flash_graphics.ocd
|
|
```
|
|
|
|
## Connect the STLinkV2 to the PineTime
|
|
Here is an example using the pogo pins:
|
|
|
|
|
|
|
|
You can find more information about the SWD wiring [on the wiki](https://wiki.pine64.org/index.php?title=PineTime_devkit_wiring). |